HBM MP85A - Page 160

To Previous Page

www.hbm.com

HBM Test and Measurement

Tel. +49 6151 803-0

Fax +49 6151 803-9100

info@hbm.com

measure and predict with confidence

A0293_06_E00_03 HBM: public

Main Page

Table of Contents3
Safety Instructions8
Markings Used12
Markings Used in this Document12
Symbols on the Device12
Introduction14
About this Documentation14
Scope of Supply14
Accessories15
General16
Installing/Removing the MP85A (Schematic Diagrams)18
Mechanical Installation/Removal18
Connecting Several Devices20
Electrical Connection21
General Notes on Connection21
Overview of MP85A(-S) Functions22
Overview of MP85ADP(-S)/MP85ADP-PN(-S) Functions23
Supply Voltage and Control Inputs/Outputs24
Connecting the Power Supply25
External Supply Voltage for Control Outputs25
Reference Potential for Control Inputs/Switch Test Inputs26
Transducer27
Synchronization of Carrier Frequencies27
Strain Gage and Displacement Transducers, Potentiometric and LVDT Sensors27
Incremental, SSI and DC Sensors31
Piezoelectric Measurement Chains33
TEDS (Transducer Electronic Data Sheet) Chips37
TEDS Connection37
Parameterization with TEDS38
Interfaces40
Ethernet Interface40
CAN Interface42
PROFIBUS Interface (MP85ADP/MP85ADP-S Only)43
Profinet Interface (MP85ADP-PN/MP85ADP-PN-S Only)45
Switch Settings/Replacing the Battery47
Changing the Supply Voltage for Active Sensors47
Replacing the Battery48
CAN Termination Resistor49
Starting Up/Setup Mode50
Operation52
Device Settings, Measured Values, Process Status, PROFIBUS52
Memory Card, Error Types, Firmware Update, Device Backup52
Overview of All Groups and Parameters59
Setting Parameters on the Device61
Hardware Setup62
Power Supply/Transducers62
Connection Via Ethernet63
Connecting the CAN Adapter (USB)63
Installing the PME Assistant Software64
Using the PME Assistant65
Using the Ethernet Interface66
Using the USB Interface66
Automatic Version Detection68
Firmware Updates68
Offline Mode70
Measurement Procedure71
Data Reduction71
Classification74
Limit Monitoring in Real Time75
Hiding External Tolerances75
Evaluation Criteria77
Measurement Programs (Parameter Sets)82
Switch Test (Easyswitch)85
Switch Test85
Haptic Test88
Communication with a Control System90
MP85A Process Controller in the Machine Control System90
Test Process Sequence over Time93
Transducer Test95
Zero Balance96
Simulation of Digital Outputs97
Parameter Sets (Measurement Programs)97
Evaluation/Backup Process Times100
Process Data Backup/Production Data Management103
Display and Control Options105
Fastpress Suite Software105
Error Messages/Operating State (LED Display)107
Faqs: Frequently Asked Questions (MP85A and PME Assistant)113
How Do I Set the Interface on the MP85A113
How Do I Set an IP Address on My PC115
How Do I Connect the PME Assistant to the MP85A116
How Can I Find the File System on My PC, and Which Should I Use117
When I Launch the PME Assistant, What Do the Options Do118
What Happens if I Connect Via an Existing Ethernet Connection119
What Are the Requirements for an MMC/SD Card120
What Is the Relationship between the Data Rate and the Filter Settings120
What Does Data Reduction Do and How Do I Set It121
What Options Are There for Starting, Stopping and Ending Measurement124
How Do I Work in Setup Mode133
How Long Does Zero Balance Take and What Does It Involve134
What Takes Place During a Transducer Test and What Are the Important Points134
What Are the Limitations for (Transducer) Scaling135
What Must I Bear in Mind When Switching Parameter Sets135
How Can I Find Out/Track Changes to Device Settings136
What Error Messages Are There for Measurement/The Process Status, and How Can I Correct Errors137
What Do the Error Messages for Tolerance Window Violations Mean139
What Do the Leds on the MP85A Mean141
What Do I Have to Look out for When Saving Process Data (Curves/Results)144
What Does the Flow Diagram of a Process-Optimized Measurement Look Like145
What Does the Flow Diagram of a Measurement with no Data Loss Look Like146
What Causes a Digital Output to be Set146
How Can I Generate a Log Printout of a Process147
How Can I Transfer All the Settings of One MP85A to Another Device (Cloning)147
How Do I Do a Firmware Update, and Can It be Prevented148
Downloading the Firmware Update148
Procedure for Updating the Firmware149
What Does a Tolerance Band Look Like150
What Does an Envelope Curve Look Like150
What Is TEDS150
Software and Firmware Updates152
Waste Disposal and Environmental Protection154
Technical Support155
Index156

HBM MP85A - Page 160

Table of Contents

Related product manuals