Hitachi PXR-D User Manual

● Setting Character Height and Character Orientation 3-38
5
4
3
Press ↓ .
The cursor then moves to the character width input field.
Press 0 , 1 , and 0 in sequence.
The character width is then set to 10.
Press ↓ .
The cursor then moves to the character orientation input field.
Print specifications 2011.07.07 12:45
Manual
Character height [ ９０] (０-９９)
Character width  [０１０] (０-１９９)
Status: Ready Com=0
Message name
［  ］
Start
up
Shut
down
Comm
On/Off
7
6
Press ↓ .
This places the cursor in the repeat intervals input field.
Press 1 .
Character orientation option 1 (ABC) is then selected.
¡ The same result is produced if you press Increment .

Print specifications 2011.07.07 12:45
Character height [ ９０] (０-９９)
Character width
 [０１０] (０-１９９)
Character orientation [１] (０:ＡＢＣ １:ＡＢＣ ２: ３: )
（Arrow: Printing direction） → ← ← →
ＡＢＣＡＢＣ
Manual
Apply
Status: Ready Com=0
Message name
［  ］
Start
up
Shut
down
Comm
On/Off
2
1
(2) Operating procedure
¡ Setting the character height to 90, character width to 10, character orientation to 1.
From the "Print description" screen, press Print spec .
The "Print specifications" screen then opens. (The maximum value for the print
start delay varies with the character size.)
Print specifications 2011.07.07 12:45
Back
1234567890
Incre-
ment
Decre-
ment
Character
unit CH
Scanning
unit SC
Manual
Show
cursor
Status: Ready Com=0
Message name
［  ］
Start
up
Shut
down
Comm
On/Off
Character height [ ８５] (０-９９)
Character width
 [０００] (０-１９９)
Character orientation [０] (０:ＡＢＣ １:ＡＢＣ ２: ３: )
（Arrow: Printing direction） → ← ← →
Printing method ２ (1: single scan 2: Interlaced )
Repeat intervals [００００] (scanning unit SC 0-9999)
Repeat count [００００] (0: none, 1-9998, 9999: continuous)
Print start delay [００５０] (scanning unit SC 0-9999)
Target sensor timer [０００] (1/10 sec 0: none, 1-999
)
Target sensor filter [１] (1: time setup, 2:until end of print. )
Setup value [００００] (msec 0-9999)
ＡＢＣＡＢＣ
Prev.
set-
ting
Next
set-
ting
↓
↑
→
←
Press 9 and 0 in sequence.
The character height is then set to 90.
Print specifications 2011.07.07 12:45
Manual
Character height [ ９０] (０-９９)
Character width  [０００] (０-１９９)
Status: Ready Com=0
Message name
［  ］
Start
up
Shut
down
Comm
On/Off
If the cursor is not
displayed, press
Show cursor .
Operations for
modifying the setting
contents
(See Section 2.1.3,
Operations for
modifying the setting
contents. )
Cursor will move to the
line you touched.
Selected item on the
cursor-positioned line
can be changed
by touching.
Cursor will move to the
line you touched.

Hitachi PXR-D Specifications

General

Brand	Hitachi
Model	PXR-D
Category	Printer
Language	English