Honeywell FS24X Plus

To Next Page

To Previous Page

Honeywell® FS24XPlus™ | User Manual

Note: On power-up, the FS24XPlus™ flame detector will run a start-up routine during which current levels maybe not be stable. The

controller should also be set to filter milliamp transients of less than 1 millisecond.

Main Page

Table of Contents2
Introduction6
Safety6
For Additional Cautions and Warnings, See Appendices 1 and6
Disclaimer8
Warranty8
Copyright Notice9
Applications9
Security Guide10
Specifications11
Product Overview14
What's in the Box14
Features and Benefits14
Self-Test15
Available Spares/Accessories15
Installation and Commissioning16
Mounting16
Opening the Detector17
Installation Summary18
Wiring19
Commissioning the Detector23
Analog Output: Flame Detected23
Detector Module Replacement24
Configuration and Operation25
Test Lamp Operation25
Declaration of Conformity26
Maintenance26
FS24X Plus™ Material Numbers26
Product Label27
Appendix 1: Hazardous Location Installation for FS & SS Series Flame Detectors and Associated Test Lamps28
Overview28
Safety28
Nameplate Tag29
Generic Nameplate View30
Electrical Ratings30
Installing the Flame Detector31
Appendix 2: FM Performance for FS24X Plus32
Product Overview32
Safety32
Hazardous Classifications33
Performance Specifications33
Available Accessories/Spares35
What's in the Box35
Installation35
Wiring36
Wiring Configurations37
Communication Wiring38
Configure the Detector (Safe Area)40
Commissioning the Detector40
States & Outputs40
Test Lamps40
Maintenance41
Flame Response Sensitivity42
False Alarm Stimuli Response43
Appendix 3: Honeywell® Flamemanager45
Install the Honeywell® Flamemanager Application45
Appendix 4: HART® User Information54
Edd/Dtm54
Access Levels and Password Protection54
Menu Structure55
Menu Navigation59
Error Reporting59
Connection59
Appendix 5: HART® Developer Information60
Hart60
Device Identification60
Universal Commands60
Device-Specific Commands61
Additional Device Status (Command #48)62
Command #128: Read Fire Alarm Status63
Command #130: Read Device Status64
Command #135: Read Inhibit Status65
Command #136: Simulate 4-20 Ma66
Command #137: Read Internal Commination Fault Status67
Command #138: Read Voltage Fault Status68
Command #139: Read Test Lamp Detection Status69
Command #140: Read Temperature70
Command #141: Read Voltage70
Command #142: Read All Sensor Readings71
Command #144: Read Model72
Command #153: Read Device Alarm State72
Command #154: Set Detector Sensitivity73
Command #155: Read Detector Sensitivity74
Command #158: Set Relay Default State75
Command #159: Read Relay Default State76
Command #161: Reset Latch76
Command #162: Set Password77
Command #164: Read Event History78
Command #165: Force Relay State79
Command #166: Force 4-20 Ma - Specific Loop Current79
Command #167: Force HALO State80
Command #168: Write Ma Configuration81
Command #169: Configure Alarm, Warning State - Latch/Unlatch81
Command #173: Read HALO Mode for Normal82
Command #174: Set Date Format83
Command #175: Set RTC (Time and Date)83
Command #176: Read RTC (Time and Date)84
Command #177: Configure HALO Mode for Alarm85
Command #178: Read HALO Mode for Alarm85
Command #179: Read Alarm, Warning State - Latch/Unlatch86
Command #180: Start/End Inhibit87
Command #181: Read Inhibit Timeout87
Command #182: Configure Inhibit Timeout88
Command #183: Read Ma Configuration89
Command #187: Read Force Timeout90
Command #188: Configure Force Timeout90
Command #189: Read Relay State91
Command #190: Write Login92
Command #191: Read Date Format92
Command #192: Read Relay3 (Aux) Input Selection93
Command #193: Set Relay3 (Aux) Input Selection94
Command #195: Set Alarm Verification Time94
Command #196: Write LED Intensity95
Command #197: Read LED Intensity96
Command #198: Read Serial Number97
Common-Practice Commands97
Tables98
Performance99
Appendix 6: Overview of the FS24X Plus™ Modbus Interface100
Appendix 7: Fault Conditions102
Appendix 8: Certifications and Approvals103
Hazardous Area103
Contact Us107

Honeywell FS24X Plus - Page 20

Table of Contents

Related product manuals