Need help?Do you have a question about the HydroPoint WeaterTRAK ET plus and is the answer not in the manual?
Details the main controls and features of the WeatherTRAK ET plus controller.
Explains how to navigate and modify the controller's settings using its interface.
Configures the primary start time for irrigation cycles managed by the controller.
Defines a specific time frame during which irrigation is permitted to operate.
Establishes a secondary start time for watering during periods of high evapotranspiration.
Sets the accurate date and time for the controller's operation and scheduling.
Configures the controller to the correct local time zone for accurate operations.
Enables or disables automatic adjustment for Daylight Saving Time.
Specifies the total number of active stations wired to the controller.
Displays the unique serial number of the WeatherTRAK ET plus controller.
Shows the signal strength for wireless reception, important for ET Everywhere service.
Selects a specific phase for activation, used during ET Everywhere service setup.
Shows the controller's specific location identifier for ET updates.
Displays the current software version of the WeatherTRAK ET plus controller.
Configures sequential versus simultaneous station operation for irrigation schedules.
Assigns a water district number for participation in agency programs.
Configures the controller to use either the internal or an external radio antenna.
Final step to activate the controller with the ET Everywhere service.
Defines water day patterns for irrigation schedules (A and B).
Overview of the different programming modes and their functionalities.
Automates irrigation programming based on landscape parameters and ET data.
Allows manual entry of irrigation parameters, adjusted by ET Everywhere service.
Manual irrigation programming without ET service adjustments.
Duplicates station settings to other stations for efficient programming.
Displays detailed irrigation schedule information for each station.
Fine-tunes station runtimes in "Fully Automated" mode by percentage.
Displays the current operational status and active stations of the controller.
Allows immediate manual start of irrigation for specific stations or all stations.
Temporarily suspends all irrigation for a set number of days.
Provides status alerts for key controller functions and potential issues.
Allows viewing of current daily and weekly evapotranspiration (ET) values.
Adjusts the contrast of the controller's display for better readability.
Accesses support information and contact details for HydroPoint Customer Service.
Stops all controller operations until switched back to RUN or another mode.
Enables the WeatherTRAK Rain Service for rainfall monitoring.
Configures the controller's zip code for local ET data.
Sets the ET zone number for receiving local ET updates.
Shows the assigned group number for grouping controllers for ET messages.
Sets a backup ET value for communication failure events.
Initial steps for setting up the irrigation system and controller.
Guides through the basic controller configuration steps.
Instructions for activating the controller with customer service.
Explains how to set water day patterns for irrigation schedules.
Details on modifying station-specific irrigation program settings.
Features for copying program settings between stations or restoring defaults.
How to view projected irrigation schedules for each station.
Fine-tuning station watering times in 5% increments for auto mode.
Instructions for manual irrigation operation for specific or all stations.
Steps to suspend irrigation for a specified duration.
Guidance on diagnosing and resolving various status alerts from the controller.
Steps to troubleshoot why stations fail to irrigate despite correct programming.
Adjusting settings to correct over-watering issues in the landscape.
Adjusting settings to correct under-watering issues in the landscape.
Troubleshooting steps if the feature adjustment function is unresponsive.
Resolving issues with a newly installed and activated controller that is beeping.
Explains the different beep codes and their meanings for controller status.
Steps to diagnose and fix a blank display screen on the controller.
Troubleshooting steps for a controller display that has become unresponsive.
Explains the meaning of the "P" indicator in the ET display.
Understanding discrepancies in Week 1 data within the Review screen.
Explains the "99+" indication for runtime in the Review screen.
Overview of collecting site-specific data for irrigation program calculation.
Outlines the methods for gathering precipitation rate and other site data.
Details electrical specifications and fuse replacement for the controller.
General| Manufacturer | HydroPoint |
|---|---|
| Category | Weather Station |
| Installation | Professional installation recommended |
| Model | WeatherTRAK ET Plus |
| Connectivity | Ethernet |
| Sensors | Rainfall, Temperature, Humidity, Solar Radiation, Wind Speed, Wind Direction |
| Power Source | Battery Backup |
| Weather Data | Evapotranspiration (ET), rainfall, temperature, solar radiation, wind speed |
| User Interface | Web-based interface |
To Next Page