Hypertherm HyPerformance Plasma HPR400 User Manual

OperatiOn
HPR400XD Auto Gas – 806160 4-47
Metric
English
Select
Gases
Set
Preflow
Set
Cutflow
Minimum
Clearance
Equivalent
Material
Thickness
Torch-to-Work
Distance
Cutting
Speed
Initial Pierce
Height
Pierce Delay
Time
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
mm mm Range (mm) mm/m mm factor % seconds
O
2
Air 15
23
84
21
2.0
3 2.5 – 8.6 6505 5.0
200
0.1
4
2.8 – 8.6
5550
5.6
0.2
5 4795
0.3
6 4035
15
8
3.0 – 8.6
3360
6.0
10 2680
12 3.3 – 8.6 2200 6.6 0.5
15
3.8 – 8.6
1665
7.6
0.7
20 1050 1.0
25 4.0 – 8.6 550 190 1.8
33
32
*
4.5 – 8.6
375 10.2 220 4.0
38 255 Edge start
Select
Gases
Set
Preflow
Set
Cutflow
Minimum
Clearance
Equivalent
Material
Thickness
Torch-to-Work
Distance
Cutting
Speed
Initial Pierce
Height
Pierce Delay
Time
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
Plasma
gas
Shield
gas
in in Range (in) ipm in factor % seconds
O
2
Air 15
23
84
21
0.08
0.135 0.10 – 0.34 240 0.20
200
0.1
3/16
0.11 – 0.34
190
0.22
0.2
1/4 150
0.3
15
5/16
0.12 – 0.34
132
0.24
3/8 110
1/2 0.13 – 0.34 80 0.26 0.5
5/8
0.15 – 0.34
60
0.30
0.7
3/4 45 1.0
1 0.16 – 0.34 20 190 1.8
33
1-1/4*
0.18 – 0.34
15 0.40 220 4.0
1-1/2 10 Edge start
Mild steel bevel cutting
O
2
Plasma / Air Shield
130 A
Flow rates – lpm/scfh
O
2
Air
Preflow 0 / 0 64 / 135
Cutflow 33 / 70 45 / 96
220742
220637
220649220740 220179220646
Note: Bevel angle range is 0° to 45°.
220700
Select
Gases
Set
Preflow
Set
Cutflow
Amperage
Torch-to-Work
Distance
Marking
Speed
Arc
Voltage
Amps mm in mm/m ipm Volts
N
2
N
2
10 10 10 10 15 2.5 0.10 6350 250 130
Ar Air 50 10 50 10 15 3.0 0.12 2540 100 75
Marking
* Suggestions for piercing 32 mm (1-1/4 in) mild steel: 1. Turn preflow on during IHS, 2. Use ohmic contact during IHS,
3. Use pierce complete when piercing.

Hypertherm HyPerformance Plasma HPR400 Specifications

General

Duty Cycle	100% at 400 A
Cutting Capacity	up to 50 mm (2 in)
Output Current	30-400 A
Input Voltage	200 – 480 V, 3-PH, 50/60 Hz
Gas Supply	Oxygen, Air, Nitrogen