IAI ASEP - User Manual

Other manuals for IAI ASEP

Operation Manual56 pages

First Step Guide5 pages

Questions and Answers:

T
Tina DonaldsonAug 27, 2025
How to fix excitement detection error in IAI ASEP Controller?
- K
  Kathryn RobertsAug 27, 2025
  Check for the motor connecting cable wiring condition. Confirm that there is no error in the mechanical part assembly condition. Move the actuator away from the mechanical end and re-input the power. In the case that the load weight is normal, move the actuator by hand to check the sliding resistance after the power is turned OFF. In the case that there is any error in the actuator itself, contact our company in case of Excitement Detection Error in IAI Controller.
J
Julie MurraySep 15, 2025
How to resolve A, B, or Z-phase wire breakage in IAI ASEP?
- J
  Joel MitchellSep 15, 2025
  Check for the connection condition of the actuator connecting cable and perform the continuity test. If normal, contact our company in case of A, B or Z-phase Wire Breakage in IAI Controller.
R
Regina ButlerAug 28, 2025
How to resolve software stroke limit over error in IAI ASEP?
- H
  heidifloresAug 28, 2025
  If the actuator is vertically installed and the target position is close to the soft limit, because the load is too high, or the deceleration setting is too high, an over-chute might occur and the actuator might exceed the soft limit. Set the deceleration curve so that an over-chute is not caused when the actuator is stopped. Return the actuator within the soft limit range and perform the servo-motor turning ON operation in case of Software Stroke Limit- Over Error in IAI Controller.
C
Christine BowmanAug 28, 2025
How to fix absolute encoder error detection 1 in IAI Controller?
- B
  Brian CarneyAug 29, 2025
  Turn OFF the power and arrange so that a vibration is not added to the actuator and turn ON the power again. Arrange so that a vibration is not added to the actuator and perform the home return operation again in case of Absolute Encoder Error Detection 1 in IAI Controller.
P
Peter RuizSep 23, 2025
What to do if IAI Controller experiences A and B-phase wire breaking?
- C
  Carolyn GibsonSep 23, 2025
  If the IAI Controller experiences A and B-phase wire breaking, it means the encoder signal is not being detected properly. Check the condition of the actuator connection cable and perform a continuity check. If no abnormalities are detected, contact support.
K
Karen MartinezSep 18, 2025
What to do if PC board mismatching error in IAI ASEP Controller?
- C
  christopherbooneSep 22, 2025
  Contact our company in case of PC Board Mismatching Error in IAI Controller.
Z
Zachary ThomasSep 13, 2025
What to do for control power source voltage drop in IAI ASEP?
- A
  angelagallowaySep 13, 2025
  Check for the actuator cable wiring condition. In the case that the voltage is normal, contact our company in case of Control Power Source Voltage Drop in IAI Controller.
S
Sandra MooreSep 10, 2025
What to do if IAI Controller has pressing motion range over error?
- N
  Natasha EdwardsSep 12, 2025
  Revise the construction of the whole system.
B
Brian RiveraAug 30, 2025
How to resolve non-volatile memory data breakdown in IAI ASEP Controller?
- B
  Brooke BartlettAug 30, 2025
  When the error is caused even when the power is re-input, contact our company in case of Non-Volatile Memory Data Breakdown in IAI Controller.
C
Caroline RogersAug 31, 2025
How to resolve non-volatile memory write verification error in IAI Controller?
- J
  janewilliamsAug 31, 2025
  When the error is caused even when the power is re-input, contact our company in case of Non-Volatile Memory Write Verification Error in IAI Controller.

IAI ASEP Specifications

General

Operating Temperature	0 to 40°C
Storage Temperature	-10 to 60°C
Vibration Resistance	4.9 m/s² (0.5 G) or less
Protection Class	IP20
Number of Axes	1
Communication Interface	Ethernet, RS-232C
Power Supply	24V DC
Humidity	20 to 80% RH (non-condensing)
Control Method	Position, Speed, and Torque Control
Programming Language	Proprietary language (IAI language)