IAI X-SEL User Manual (English)

Other manuals for IAI X-SEL

Questions and Answers:

D
dballAug 22, 2025
What to do if IAI X-SEL displays error 914 CA2?
- M
  marshalljennyAug 22, 2025
  If your IAI Controller displays error code 914 CA2, it could be due to several reasons: the PG cable might be disconnected, an absolute reset hasn't been performed after the initial setup, or the voltage of the absolute-data backup battery is low. To resolve this, connect the PG cable to the controller and perform an absolute reset. If the problem persists, replace the absolute-data backup battery and then execute another absolute reset.
L
Linda JohnstonAug 23, 2025
Why does my IAI Controller show ACF error?
- R
  Robert WoodAug 25, 2025
  The ACF error on your IAI Controller typically indicates a momentary power failure or a voltage drop. This can also occur if you are inputting 100V into a controller that requires 200V. To fix this, check the power source voltage. Note that if the last digit of your controller's model number is '-1,' it requires 100V, while '-2' indicates a 200V specification.
J
Jennifer GlennAug 25, 2025
What to do if IAI X-SEL Controller displays error d10?
- H
  Heather MurrayAug 26, 2025
  If your IAI Controller displays error d10, it may be due to a damaged motor coil or a faulty power stage board. First, measure the relative resistance among phases U/V/W. If the resistance values differ, the coil is likely burned, and you should replace the motor. However, if the resistance values are nearly identical, the coil is likely fine, and you should replace the power stage board (where the motor power cable connects).
J
Jessica RuizAug 27, 2025
What to do if IAI X-SEL displays CA5 error?
- C
  Christopher RobertsonAug 27, 2025
  If your IAI Controller displays the CA5 error, it indicates that the operation is mechanically disabled or the power stage board is faulty. First, check if the actuator mounting bolts are contacting inside the axes or if the slider attachment is contacting any surrounding mechanical parts. If there are no mechanical issues, replace the power stage board.
T
Tiffany BakerAug 27, 2025
How to fix d03 error on IAI Controller?
- J
  Jonathan FischerAug 27, 2025
  The d03 error on your IAI Controller suggests that the encoder is faulty or has dust attached. Remove the motor cover and use cleaning air spray designed for OA equipment on the cord wheel. If the problem continues, you may need to replace or readjust the encoder.
M
michael45Aug 29, 2025
What causes d18 error on IAI Controller?
- L
  Lauren FoleyAug 29, 2025
  The d18 error on an IAI Controller indicates that the driver CPU board was damaged due to noise in the encoder cable. To resolve this, replace the board and implement noise control measures.
A
Andrew PhamAug 30, 2025
What to do if IAI X-SEL displays error C9C?
- S
  Shawn BeckerAug 30, 2025
  If your IAI Controller displays error C9C, it indicates that the phase-Z position is defective or the reversing amount at home return is small. Check if any foreign objects have entered the actuator and ensure the mounting bolts are not contacting the slider. Additionally, change axis-specific parameter No. 22 to “100.”
J
jenniferwalkerAug 31, 2025
What to do if IAI Controller shows oPG error?
- S
  sjosephAug 31, 2025
  If your IAI Controller displays the 'oPG' error, it means the safety gate is open. To resolve this, check the system connector wiring.
M
Matthew WestSep 1, 2025
How to resolve d06 error on IAI X-SEL Controller?
- C
  Crystal RobertsonSep 2, 2025
  The d06 error on your IAI Controller indicates that the encoder cable is disconnected. To fix this, replace the encoder cable.
S
schambersSep 3, 2025
What does d19 error mean on IAI X-SEL?
- S
  Samuel SimmonsSep 3, 2025
  The d19 error on your IAI Controller indicates that the encoder cable is disconnected. To resolve this, replace the encoder cable.