Sequencer mode
128
SEQ Page Select
• Press the MODE SEQ switch to select Sequencer mode.
You can use the following ways to select the pages in
Sequencer mode.
1. Press the SEQ switch, and then press the MENU switch
to access “Page Select.”
“Page Select” shows an abbreviated name for each page.
The page shown in grey is the page selected just prior to
pressing the PAGE SELECT switch.
2. Select the desired page in the display.
Other ways to select pages
•Hold down the PAGE SELECT switch and press one of
the numeric keys, 0–9, to specify a page number and to
access the corresponding page.
For example, if you want to access the P3: Track Param
page, hold down the PAGE SELECT switch and press
numeric key 3.
Note: For pages that consist of multiple subpages, the
first of these pages will be selected. For example, P0–1
with a subpage of P0–2, will access P0–1.
You can press the EXIT switch to return to the P0–1:
Play/REC page you selected most recently. Press the
EXIT switch once again to return to the P0–1: Play/REC–
Program T01–08 page.
Page Main content
PLAY
P0–1: Play/REC
Song selection, playback, and recording.
(☞p.129)
Program selection for each track. (☞p. 131)
Pan and volume settings etc. for each track.
(☞p.133)
Track playback loop settings. (☞p. 134)
Tone Adjust editing. (☞p.136)
Recording method selection. (☞p.137)
P0–2: Play/REC
Control
Simple arpeggiator editing. (☞p.142)
Editing from the control surface. (☞p.143)
EDIT
P1: Controllers
SW1, 2, and knob settings. (☞p.147)
Chord trigger switch note and velocity
settings. (☞p.148)
P2: EQ EQ settings for each track. (☞p.149)
P3: Track Param
Various parameter settings for each track
(MIDI channel, OSC selection, Pitch setting,
etc.) (☞p.151)Here, you can
P4: Zone/Delay
Key split and layer settings.
(Key zone and velocity zone) (☞p.156)
Time delay from note-on to beginning of
sound. (☞p.158)
P5–1: MIDI Filter1
MIDI transmit/receive filter 1 settings.
(☞p.160)
P5–2: MIDI Filter2
MIDI transmit/receive filter 2 settings.
(☞p.164)
P6: Track Edit
Step recording.
Event recording.
Copy, delete, and other track editing.
(☞p.166)
ARP & DRUM TRACK
P7: Arpeggiator/
Drum Track
Arpeggiator settings. (☞p.168)
Drum track settings. (☞p.172)
EFFECT
P8–1: IFX
Routing1/1–5
Oscillator output bus and master effect send
level settings. (☞p.175)
Insert effect routing, selection, and settings.
(☞p.178)
P8–2: IFX
Routing2
Bus settings for oscillator output. (☞p.178)
Common FX LFO 1, 2 settings (☞p.178)
P9: MFX/TFX
Master effect routing, selection, and settings.
(☞p.180)
Total effect selection and settings. (☞p. 181)
PAT TERN&CUE
P10: Pattern/RPPR
Pattern recording and editing. (☞p.182)
RPPR settings. (☞p.185)
Converting a pattern to a drum track pattern.
(☞p.184)
P11: Cue List
Cue list settings.
Consecutive playback of multiple songs.
Converting to a song. (☞p. 188)
To Next Page
Loading...
