015: Analog Rec
(Stereo Analog Record)
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the modulation
caused by a warped turntable.
b: Flutter
This parameter enables you to set the depth of the modu-
lation caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click
noise that occurs once every rotation of the turntable.
This simulation reproduces record noise, and the noise
generated after the music on a vinyl record finishes.
Pitch/phase modulation effects
016: Chorus
(Stereo Chorus)
This effect adds thickness and warmth to the sound by mod-
ulating the delay time of the input signal. You can add spread
to the sound by offsetting the phase of the left and right LFOs
from each other.
e: L Pre Delay [msec], f: R Pre Delay [msec]
Setting the left and right delay time individually allows
you to control the stereo image.
a
Speed [RPM]
Sets the r.p.m. of a record
33 1/3, 45, 78
b
Flutter
Sets the modulation depth
0...100
☞
c
Noise Density
Sets the noise density
0...100
Noise Tone
Sets the noise tone
0...100
d
Noise Level
Sets the noise level
0...100
Src
Selects the modulation source for the noise level
Off...Tempo
Amt
Sets the modulation amount of the noise level
–100...+100
e
Click Level
Sets the click noise level
0...100
☞,
Src Off...Tempo
Selects the modulation source for the click noise level
Amt –100...+100
Sets the modulation amount of the click noise level
f
EQ Trim
Table , “Sets the EQ input level,” on page 2
0...100
g
Pre EQ Cutoff [Hz]
Sets the EQ center frequency
300...10.00kHz
Q
Sets the EQ band width
0.5...10.0
Gain [dB]
Sets the EQ gain
–18.0...+18.0dB
h
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 1
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 1
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 1
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Analog Record
Simulation
Pre EQ
Pre EQ
EQ Trim
EQ Trim
PITCH/PHASE MOD.
a
LFO Waveform
Selects LFO Waveform
Triangle, Sine
b
LFO Phase [degree] –180...+180
Sets the LFO phase difference between the left and right
☞ Fx:010
c
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed
☞ Fx:009,
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using the
tempo and notes
☞ Fx:009,
BPM
Selects MIDI Clock and assigns tempo
MIDI, 40...240
☞ Fx:009
Base Note
Selects the type of notes that specify the LFO speed ☞ Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed
☞ Fx:009
e
L Pre Delay [msec]
Sets the delay time for the left channel
0.0...50.0msec
☞
f
R Pre Delay [msec]
Sets the delay time for the right channel
0.0...50.0msec
☞
g
Depth
Sets the depth of LFO modulation
0...100
Src Off...Tempo
Selects the modulation source of the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the LFO modulation depth
h
EQ Trim
Table , “Sets the EQ input level,” on page 2
0...100
i
Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 2
–15.0...+15.0dB
Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 2
–15.0...+15.0dB
j
Wet/Dry –Wet...–1:99, Dry, 1:99...Wet
Table , “Sets the balance between the effect and dry sounds,” on page 1
☞ Fx:010,
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 1
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 1
–100...+100
Chorus
Chorus
Left
Right
LFO Phase
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ
HEQ
LEQ
HEQ
LFO: Tri / Sine
To Next Page
Loading...
Need help?
General
