Amplifier LFO1 modulation
AMS (Alternate Modulation Source)
Use this parameter to select a source that will control the
depth by which “LFO1” will modulate the volume of the
selected oscillator. See “AMS (Alternate Modulation Source)
list” on page 14-19.
Intensity
As the absolute value of this setting is increased, the effect of
“AMS” on “LFO1” will increase. Negative (–) values will
invert the LFO waveform.
-99…+99 Intensity value.
PAGE 15 - AMP LFO2
These parameters let you use “LFO1” (see “Page 17 - LFO1”
on page 14-16) and “LFO 2” (see “Page 18 - LFO2” on
page 14-18) to control the selected oscillator volume. See
“Page 14 - Amp LFO1” for more information on parameter’s
editing.
PAGE 16 - AMP EG
These parameters let you create time-varying changes in the
volume of the selected oscillator.
Selected
Use this parameter to select an oscillator to put in edit. Alter-
natively, you can select oscillators using the F1-F4 buttons.
Amp envelope
Start/Attack/Break/Sustain/Release Level
These parameters are the level of the envelope segment.
0…99 Level value.
Start Level
This parameter specifies the volume level at note-on. If you
want the note to begin at a loud level, set this to a high value.
Attack Level
This parameter specifies the volume level that will be reached
after the attack time has elapsed.
Break Level
This parameter specifies the volume level that will be reached
after the decay time has elapsed.
Sustain Level
This parameter specifies the volume level that will be main-
tained from after the slope time has elapsed until note-off
occurs.
Attack/Decay/Slope/Release Time
These parameters specify the time over which the volume
change will occur.
0…99 Time value.
Attack Time
This parameter specifies the time over which the volume will
change after note-on until it reaches the attack level. If the
start level is 0, this will be the rise time of the sound.
Decay Time
This parameter specifies the time over which the volume will
change from when it reaches the attack level until it reaches
the break point level.
Slope Time
This parameter specifies the time over which the volume will
change from when it reaches the break point level until it
reaches the sustain level.
Release Time
This parameter specifies the time over which the volume will
change after note-off until it reaches 0.
Amp EG ‘Level’ modulation
AMS(L) (Alternate Modulation Source)
This parameter specifies the source that will control the
“Level” parameters of the amp EG. See “AMS (Alternate
Modulation Source) list” on page 14-19.
Intensity
This parameter specifies the depth and direction of the effect
that “AMS” will have. For example, if “AMS” is Velocity, set-
ting “Start Level Swing”, “Attack Level Swing” and “Break
Point Level Swing” to + and setting “Intensity” to a positive
(+) value will cause the amp EG volume levels to increase as
you play more strongly. Setting “Intensity” to a negative (–)
values will cause the amp EG volume levels to decrease as you
play more strongly. With a setting of 0, the levels will be as
specified on “Page 16 - Amp EG”.
-99…+99 Intensity value.
Selected: Osc1
Intensity: +0
AMS: Joystick -Y
Intensity: +0
Amp LFO2 |Osc1
Selected: Osc1
Start Level: +99
Attack Time: 73
Attack Level: +95
Amp EG |Osc1
Note-on
Note-off
Attack
Time
Decay
Time
Release Time
Attack Level
Sustain
Level
Time
Break Point
Start
Level
Slope
Time
Amplifier EG
Volume
Amp 1 EG changes (Level) (AMS=Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Softly played note when Start Level
Swing=0 and Attack Level Swing
and Breack Level Swing are set to +
Strongly played note when Start Level
Swing=0 and Attack Level Swing and
Breack Level Swing are set to +
Strongly played note when Start Level
Swing=0 and Attack Level Swing and
Breack Level Swing are set to +
To Next Page
Loading...
