PAGE 10 - PREFERENCES
In this page, you can set various general parameters.
Use the A-D VOLUME/VALUE button pairs to select a
parameter.
Note: These settings are stored in the Global file. After changing
these settings, press WRITE to save them into the Global. The
Write Global window will appear (see “The Write window” on
page 11-3).
Note: You can always start both sequencers simultaneously.
Start both sequencers simultaneously by keeping SHIFT held
down while pressing one of the PLAY/STOP controls.
Link Mode
The two onboard Sequencers can work each with a different
Tempo (Off), or use the same Tempo (Link modes).
Off The sequencers Tempo are not linked. Each
sequencer uses its own Tempo.
Link Measure
The two sequencers Tempo are linked together.
The Tempo data written into the Songs are
ignored. Adjust the Tempo using the TEMPO/
VALUE controls.
Start one of the sequencers, by pressing its own
PLAY/STOP control. Then, start the other
sequencer, by pressing the other PLAY/STOP
control; the second sequencer starts at the next
measure.
Link Beat The two sequencers Tempo are linked together.
The Tempo data written into the Songs are
ignored. Adjust the Tempo using the TEMPO/
VALUE controls.
Start one of the sequencers, by pressing its own
PLAY/STOP control. Then, start the other
sequencer, by pressing the other PLAY/STOP
control; the second sequencer starts at the next
beat (quarter or octave, depending on the
Song’s Time Signature).
S2 FX Mode
This parameter selects the effects mode for Sequencer 2.
When a 4-effects Song is loaded, all four effects are used,
independently from this setting.
AB The A and B effect pair is used. Sequencer 2
shares its effects with Sequencer 1.
CD The C and D effect pair is used.
Note: When this parameter is set to CD,
Sequencer 2 shares its effects with the Realtime
(Keyboard) tracks, so these effects can be changed
either selecting a Song for Sequencer 2, or select-
ing a Performance (unless the “Performance FX
Mode” parameter is set to Off – see below).
Performance FX Mode
This parameter selects the effects mode for the Performance.
Off When selecting a Performance, no effect is
selected.
CD The Performance selects the C and D effect
pair.
Note: When both this parameter and the “S2 FX
Mode” parameter are set to CD, Sequencer 2
shares its effects with the Realtime (Keyboard)
tracks, so these effects can be changed either
selecting a Song for Sequencer 2, or selecting a
Performance.
Harmony Track
The Vocal Harmonizer of the Vocal/Guitar Processing Board
gets the chord notes from the track selected with this param-
eter.
Off No track sends notes to the Harmonizer.
Chords can still be received from the MIDI IN.
S1-Tr01…16 Chords are sent from one of Sequencer 1 tracks.
S2-Tr01…16 Chords are sent from one of Sequencer 2 tracks.
S1/S2Tr01…16 Notes are sent by a track with the same name
from both Sequencer 1 and Sequencer 2.
Note: If both sequencers are generating notes at
the same time, the harmonizer will receive notes
from both sequencers.
Global Chords are sent from the Chord Scanning area
of the Realtime (Keyboard) tracks. The status
of the “HarmKbd (Harmony Keyboard
Mode)” is therefore considered (see page 16-
10).
SAVING A LIST OF SONGS
How to save a list of Songs contained in a
folder
1. Press SONG PLAY to select the Song Play operative
mode.
2. Press one of the A (S1:) VOLUME/VALUE button to
select the Load Song page.
3. Use the F1 button to select the device (FD or HD) con-
taining the folder whose Song list you want to save.
4. Use the F3 (Open) and F4 (Close) buttons to browse
through the folders in the selected device.
5. Move the folder you are looking for to the first line of
the display. Use the TEMPO/VALUE controls, or the E-F
(Scroll Up) and G-H (Scroll Down) VOLUME/VALUE
buttons.
6. Once the folder is selected, press SHIFT + F2.
7. A dialog box will appear, asking you to insert a floppy
disk into the disk drive. Insert the disk, and press
ENTER to confirm, or EXIT to abort.
Note: Since you can only print the list from a personal com-
puter, it will be automatically saved into a floppy disk.
Note: The text file will contain a list of “*.mid”, “*.kar” and
“*.jbx” files only (i.e., the files you can select using the numeric
keypad – see “Selecting a Song composing its progressive num-
ber” on page 11-1). Folders and different kinds of files will not
be included.
Link Mode:Off
S2 FX Mode:CD
Perf. FX Mode:CD
Harmony Track:S1-Tr05
Preferences (Gbl)
To Next Page
Loading...
Need help?
General
