EasyManuals Logo

Korg Trinity series User Manual

Korg Trinity series
81 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #55 background imageLoading...
Page #55 background image
6. About the effects
49
STEP 3
Combination
Since the insert effect settings for each program are ignored by combinations, you will need to
make new insert effect settings.
Make effect grouping settings in Combination Edit mode P7 tab page 1 (Effect Grouping) FX Size,
and make effect routing settings in tab page 2 (Insert Effects). Then set the parameters of each
effect in tab pages 3 and following (Effect Parameter).
The effects that can be used by a combination must have a total effect size of 8 or less for all tim-
bres. Up to 3 effects can be connected in series for a timbre. (For a drum-mode program, up to 4
effects in series or in parallel.)
It is recommended that you make a group of timbres that use similar effects, and specify an insert
effect for the group. If you want to use a programs insert effect settings in a combination, use the
page menu command Copy Insert Effect. In this case, set the effect size of the timbre to a setting
equal to or greater than the effect being copied.
Insert effect settings are also made in Combination Edit mode P7, tab page 2 parameters Pan,
Width, and Send 1 and 2 (for signals after the Insert Effects).
Pan sets the stereo location, Width sets the width of the insert effects, and Send 1 and 2 determine
the send levels (input levels) to the master effects.
To bypass the insert effects, turn the effect OFF. If you are not using insert effects, set the effect size
to 0.
Song
Since the insert effect settings for each program are ignored by songs, you will need to make new
insert effect settings.
Make effect grouping settings in Sequence mode P7 tab page 1 and 2 (Effect Grouping) FX Size,
and make effect routing settings in tab page 3 (Insert Effects). Then set the parameters of each
effect in tab pages4 and following (Effect Parameter).
The effects that can be used by a song must have a total effect size of 8 or less for all tracks. It is rec-
ommended that you make a group of timbres that use similar effects, and specify an insert effect
for the group.
Width settings and Pan settings after the Insert Effects are made in Sequencer mode P7, tab pages
3. At this time, setting the Pan and Width parameters to PRG allows you to specify the Pan and
Width for each program.
Pan sets the stereo image, and width sets the width of the insert effects.
To bypass the insert effects, turn the effect OFF. If you are not using insert effects, set the effect size
to 0.
Master effect settings
The master effects are common to all modes, and are set in P8 tab page 1 (Master Effects). The
parameters of each effect are set in tab pages 2 and following (Effect Parameter).
The modulation-type effect [E1] and the reverb/delay-type effect [E2] (both are mono in, stereo
out) can be connected in either parallel or series.
Checking the box on the left of the LCD screen will route the right channel of the modulation
effect directly to the reverb/delay effect in serial.
In P8 tab page 1 of each mode, you can also set Pan 1 and 2 (after [E1], [E2]), Return 1 and 2, Low
Gain, and High Gain.
Pan 3 and 4 species the stereo position for the output jacks 3 and 4. Return 1 and 2 set the return
level (the output level of the effect sound) to the output jacks 1/L/MONO and 2/R. Low Gain and
High Gain adjust equalization. For details on send levels and pan, refer to Send and pan settings
on page 50.
If insert effects as well as master effects are being used, output jacks 1/L/MONO and 2/R will
output the sound with insert effects and master effects applied. Output jacks 3 and 4 will output
the sound with only master effects applied.
If you do not want the master effects to be applied to the sound that is output from output jacks 3
and 4 (for example when outputting a metronome sound), turn master effects OFF. However in
this case, master effects will not be applied to the output of the 1/L/MONO and 2/R output jacks
either.
To bypass the master effects, turn the effect OFF.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Korg Trinity series and is the answer not in the manual?

Korg Trinity series Specifications

General IconGeneral
Multitimbrality16 parts
MIDIIn, Out, Thru
Oscillators2 per voice
Year Released1995
Keyboard61 keys (Trinity, Trinity Plus, Trinity Pro), 76 keys (Trinity ProX)
Sequencer16-track sequencer
StorageFloppy disk drive
OutputsStereo output, 4 individual outputs
Inputs2 audio inputs
WaveformsPCM samples
FilterResonant low-pass, high-pass, band-pass
LFO2 LFOs per voice

Related product manuals