Safety
information
Introduction
Product
Information
System
design
Mechanical
Installation
Electrical
Installation
Getting
started
Optimization Parameters
Technical
data
Component
sizing
Diagnostics
UL
Information
154 Unidrive M Regen Design Guide
Issue Number: 4
Table 9-5 Menu 3 Regen parameter descriptions
Parameter Range Default Type
03.001
Reactive Power VM_POWER kVAr
RO Num ND NC PT FI
03.004
Regen Synchronization Mode
Re-synchronize (0), Delayed Trip (1), Trip (2),
Auto-synchronize (3)
Re-synchronize (0)
RW Txt US
03.005
Voltage Set Point VM_DC_VOLTAGE_SET V
200V drive: 350 V
400V drive: 700 V
575V drive: 835 V
690V drive: 1100 V
RW
Num RA US
03.006
Voltage Controller Proportional Gain Kp 0 to 65535
4000 RW
Num US
03.007
Disable Charge System / Close Contactor Off (0) or On (1)
RO
Bit ND NC PT
03.008
Charge System Disabled / Contactor Closed Off (0) or On (1)
RO
Bit ND NC
03.009
Synchronized Off (0) or On (1)
RO
Bit ND NC PT
03.010
Power Input 1 ±100.0 %
0.0 % RW
Num NC
03.011
Current Trim Mode Off (0) or On (1)
Off (0) RW
Bit US
03.012
Power Input Mode Off (0) or On (1)
Off (0) RW
Bit US
03.013
Power Input 2 ±100.0 %
0.0 % RW
Num NC
03.014
Power Input 3 ±100.0 %
0.0 % RW
Num NC
03.015
Power Input 1 Scaling 0.000 to 4.000
1.000 RW
Num US
03.016
Power Input 2 Scaling 0.000 to 4.000
1.000 RW
Num US
03.017
Power Input 3 Scaling 0.000 to 4.000
1.000 RW
Num US
03.018
Power Input kW VM_POWER kW
0.000 kW RW
Num NC
03.019
Reactive Power Input Mode Off (0) or On (1)
Off (0) RW
Bit US
03.020
Reactive Power Input kVAR VM_POWER kVAr
0.000 kVAr RW
Num NC US
03.021
Harmonic Reduction Enable Disabled (0), Imbalance Only (1), All (2)
Imbalance Only (1) RW
Txt US
03.022
Voltage Ramp Time 0.1 to 100.0 V/ms
1.0 V/ms RW
Num US
03.023
Regen Supply Loss AC Level VM_AC_VOLTAGE_SET V
200V drive: 75 V
400V drive: 150 V
575V drive: 225 V
690V drive: 225 V
RW
Num RA US
03.024
Regen Minimum Frequency 10 to 200 Hz
40 Hz RW
Num US
03.025
Regen Maximum Frequency 10 to 200 Hz
70 Hz RW
Num US
03.026
Regen Minimum Voltage VM_AC_VOLTAGE V
0V RW
Num RA US
03.027
Regen Maximum Voltage VM_AC_VOLTAGE V
0V RW
Num RA US
03.028
Supply Voltage VM_AC_VOLTAGE_SET V
200V drive: 230 V
50 Hz - 400V drive: 400 V
60 Hz - 400V drive: 460 V
575V drive: 575 V
690V drive: 690 V
RW
Num RA US
03.029
Supply Voltage Detection Mode Measured (0), User (1), User Delayed (2)
User Delayed (2) RW
Txt US
03.030
Island Detection Enable Off (0) or On (1)
Off (0) RW
Bit US
03.031
Island Detection Injection Frequency 1Hz (0), 2Hz (1), 4Hz (2)
1Hz (0) RW
Txt US
03.032
Island Detection Level 0 to 100 %
RO
Num ND NC PT
03.033
Island Detection Synchronization Source Select
Disabled (0), Slot 1 (1), Slot 2 (2), Slot 3 (3),
Slot 4 (4)
Disabled (0) RW
Txt US
03.034
Island Detect Synchronization Source
Disabled (0), Slot 1 (1), Slot 2 (2), Slot 3 (3),
Slot 4 (4)
RO
Txt ND NC PT
03.035
Synchronization Headroom 0.0 to 25.0 %
5.0 % RW
Num US
03.036
Estimated Supply Voltage VM_AC_VOLTAGE V
RO
Num ND NC PT
03.037
Positive Phase Sequence Volts VM_AC_VOLTAGE V
RO
Num ND NC PT FI
03.038
Negative Phase Sequence Volts VM_AC_VOLTAGE V
RO
Num ND NC PT FI
03.039
Negative Phase Sequence Current Gain 0.00 to 1.00
0.05 RW
Num US
RW Read / Write RO Read only Num Number parameter Bit Bit parameter Txt Text string Bin Binary parameter FI Filtered
ND No default value NC Not copied PT Protected parameter RA Rating dependent US User save PS Power-down save DE Destination
To Next Page
Loading...
