Nidec Unidrive M600 Series - 9.11 Menu 11: General drive set-up

Safety
information
Introduction
Product
Information
System
design
Mechanical
Installation
Electrical
Installation
Getting
started
Optimization Parameters
Technical
data
Component
sizing
Diagnostics
UL
Information
234 Unidrive M Regen Design Guide
Issue Number: 4
9.11 Menu 11: General drive set-up
Parameter Range Default Type
11.001 Option Synchronisation Select
Not Active (0), Slot 1 (1), Slot 2 (2), Slot 3 (3),
Slot 4 (4), Automatic (5)
Slot 4 (4) RW Txt US
11.002 Option synchronisation Active
Not Active (0), Slot 1 (1), Slot 2 (2), Slot 3 (3),
Slot 4 (4)
RO Txt ND NC PT
11.018 Status Mode Parameter 1 0.000 to 59.999 0.000 RW Num PT US
11.019 Status Mode Parameter 2 0.000 to 59.999 0.000 RW Num PT US
11.020
Reset Serial Communications*
Off (0) or On (1) RW Bit ND NC
11.021 Parameter 00.030 Scaling 0.000 to 10.000 1.000 RW Num US
11.022 Parameter Displayed At Power-up 0.000 to 0.080 0.011 RW Num PT US
11.023
Serial Address*
1to247 1 RW Num US
11.024
Serial Mode*
82NP(0), 81NP(1), 81EP(2), 81OP(3),
82NPM(4), 81NPM(5), 81EPM(6),
81OPM(7), 72NP(8), 71NP(9),
71EP(10), 71OP(11), 72NPM(12),
7 1 NP M (13), 7 1 EP M (14), 7 1 OP M (15)
82NP(0) RW Txt US
11.025
Serial Baud Rate*
300 (0), 600 (1), 1200 (2), 2400 (3), 4800 (4),
9600 (5), 19200 (6), 38400 (7), 57600 (8),
76800 (9), 115200 (10)
19200 (6) RW Txt US
11.026
Minimum Comms Transmit Delay*
0 to 250 ms 2 ms RW Num US
11.027
Silent Period*
0 to 250 ms 0 ms RW Num US
11.028 Drive Derivative 0 to 255 RO Num ND NC PT
11.029 Software Version 0 to 99999999 RO Num ND NC PT
11.030 User Security Code 0 to 2147483647 RW Num ND NC PT US
11.031 User Drive Mode
Open-loop (1), RFC-A (2), RFC-S (3),
Regen (4)
RW Txt ND NC PT
11.032 Maximum Heavy Duty Rating 0.000 to 99999.999 A RO Num ND NC PT
11.033 Drive Rated Voltage 200 V (0), 400 V (1), 575 V (2), 690 V (3) RO Txt ND NC PT
11.034 Software Sub-version 0 to 99 RO Num ND NC PT
11.035 Number Of Power Modules Test -1 to 20 -1 RW Num US
11.036 NV Media Card File Previously Loaded 0 to 999 0 RO Num NC PT
11.037 NVMediaCardFileNumber 0to999 0 RW Num
11.038 NV Media Card File Type
None (0), Open-loop (1), RFC-A (2),
RFC-S (3), Regen (4), User Prog (5),
Option App (6)
RO Txt ND NC PT
11.039 NV Media Card File Version 0 to 9999 RO Num ND NC PT
11.040 NV Media Card File Checksum -2147483648 to 2147483647 RO Num ND NC PT
11.042 Parameter Cloning
None (0), Read (1), Program (2), Auto (3),
Boot (4)
None (0) RW Txt NC US
11.043 Load Defaults None (0), Standard (1), US (2) None (0) RW Txt NC
11.044 User Security Status
Menu 0 (0), All Menus (1),
Read-only Menu 0 (2), Read-only (3),
Status Only (4), No Access (5)
RW Txt ND PT
11.045 Select Motor 2 Parameters Motor 1 (0), Motor 2 (1) Motor 1 (0) RW Txt US
11.046 Defaults Previously Loaded 0 to 2000 RO Num ND NC PT US
11.047 Onboard User Program: Enable Stop (0), Run (1) Run (1) RW Txt US
11.048 Onboard User Program: Status -2147483648 to 2147483647 RO Num ND NC PT
11.049 Onboard User Program: Programming Events 0 to 65535 RO Num ND NC PT
11.050
Onboard User Program: Freewheeling
Tasks Per Second
0 to 65535 RO Num ND NC PT
11.051 Onboard User Program: Clock Task Time Used 0.0 to 100.0 % RO Num ND NC PT
11.052 Serial Number LS 000000000 to 999999999 RO Num ND NC PT
11.053 Serial Number MS 0 to 999999999 RO Num ND NC PT
11.054 Drive Date Code 0 to 65535 RO Num ND NC PT
11.055 Onboard User Program: Clock Task Scheduled Interval 0 to 262140 ms RO Num ND NC PT
11.056 Option Slot Identifiers
1234 (0), 1243 (1), 1324 (2), 1342 (3),
1423 (4), 1432 (5), 4123 (6), 3124 (7),
4132 (8), 2134 (9), 3142 (10), 2143 (11),
3412 (12), 4312 (13), 2413 (14), 4213 (15),
2314 (16), 3214 (17), 2341 (18), 2431 (19),
3241 (20), 3421 (21), 4231 (22), 4321 (23)
1234 (0) RW Txt PT
11.060 Maximum Rated Current 0.000 to 99999.999 A RO Num ND NC PT
11.061 Full Scale Current Kc 0.000 to 99999.999 A RO Num ND NC PT
11.062 Power Board Software Version Number 0.00 to 99.99 RO Num ND NC PT
11.063 Product Type 0 to 255 RO Num ND NC PT