Piper ARROW III - Page 6

LIST OF ILLUSTRATIONS (CONT)
Aerofiche
Fgure Grid No.
5-8. Stabilator Trim Control...................................................................................................... 1G3
5-9. Rudder and Steering Pedal Assembly ............................................................................... 1G5
5-10. Rudder Controls................................................................................................................. 1G7
5-11. Rudder Rigging Tool......................................................................................................... 1G8
5-12. Clamping Rudder Pedals................................................................................................... 1G8
5-13. Rudder and Stabilator Travel Adjustments........................................................................ 1G10
5-14. Rudder Trim Control......................................................................................................... 1G11
5-15. Flap Controls..................................................................................................................... 1G13
5-16. Flap Step Adjustment........................................................................................................ 1G14
5-17. Flap Rigging Tool.............................................................................................................. 1G14
5-18. Fabricated Aileron Bellcrank Rigging Tool...................................................................... 1G16
5-19. Fabricated Aileron and Flap Rigging Tool........................................................................ 1G17
5-20. Fabricated Stabilator Rigging Tool.................................................................................... 1G18
5-21. Fabricated Rudder Rigging Tool....................................................................................... 1G19
6-1. Schematic Diagram of Hydraulic System (Prestolite)....................................................... 1H8
6-1a. Schematic Diagram of Hydraulic System (Oildyne)......................................................... 1H9
6-2. Hydraulic System Installation ........................................................................................... 1H10
6-2a. Hydraulic System Installation (SN’s 2837001 & up, PA-28R-201) and
(SN’s 2803001 & up, PA-28R-201T and up.)................... 1H11
6-3. Hydraulic Pump/Reservior Exploded Vew (Prestolite)..................................................... 1H14
6-3a. Hydraulic Pump/Reservoir Exploded View (Oildyne)...................................................... 1H15
6-4. Tests and Adjustments of Hydraulic Pump....................................................................... 1H16
6-5. Checking Aligning Brackets of Gear Back-Up Extender Actuator................................... 1H21
6-6. Gear Back-Up Extender Actuator...................................................................................... 1H22
6-7. Nose Gear Actuating Cylinder .......................................................................................... 1I3
6-8. End Gland Locking Device............................................................................................... 1I5
6-9. Main Gear Actuating Cylinder.......................................................................................... 1I6
6-10. Gear Back-Up Extender Actuator Aligning Tool.............................................................. 1I19
7-1. Nose Gear Oleo Strut Assembly........................................................................................ 1J3
7-2. Nose Gear Installation....................................................................................................... 1J6
7-3. Nose Gear Adjustment (PA-28R-201)............................................................................... 1J9
7-4. Nose Gear Adjustment (PA-28R-201T)............................................................................ 1J10
7-5. Clamping Rudder Pedals in Neutral Position.................................................................... 1J12
7-6. Rudder Pedals at Neutral Angle........................................................................................ 1J12
7-7. Nose Gear Door Retraction Mechanism (PA-28R-201).................................................... 1J13
7-8. Nose Gear Door Retraction Mechanism (PA-28R-201T)................................................. 1J14
7-9. Main Gear Oleo Strut Assembly ....................................................................................... 1J15
7-10. Main Gear Installation....................................................................................................... 1J17
7-11. Aligning Main Gear........................................................................................................... 1J19
7-12. Adjustment of Nose Gear Down Limit Switch ................................................................. 1K6
7-13. Adjustment of Main Gear Down Limit Switch................................................................. 1K6
7-14. Flap Torque Tube Cam Gear Warning Switch Installation................................................ 1K8
7-15. Throttle Warning Switch................................................................................................... 1K9
7-16. Nose Wheel Assembly ...................................................................................................... 1K11
7-17. Main Wheel Assembly...................................................................................................... 1K12
7-18. Wheel Brake Assembly..................................................................................................... 1K13
7-19. Removal of Anchor Bolt ................................................................................................... 1K15
Revised: 2/13/89
1A6