LIST OF ILLUSTRATIONS (cont)
Aerofiche
Figure Grid No.
7-20. Installation of Anchor Bolt................................................................................................ 1K16
7-21. Brake System Installation.................................................................................................. 1K18
7-22. Brake Master Cylinder (Hand/Parking Brake).................................................................. 1K19
7-23. Toe Brake Installation........................................................................................................ 1K20
7-24. Brake Cylinder (1700) (Toe Brake)................................................................................... 1K21
7-25. Brake Cylinder (10-27) (Toe Brake)................................................................................. 1K21
7-26. Bleeding Brakes................................................................................................................. 1L1
7-27. Nose Gear Service Tolerances........................................................................................... 1L9
7-28. Main Gear Service Tolerances........................................................................................... 1L12
8-1. Engine Cowling Installation.............................................................................................. 2A13
8-3. Propeller Installation ......................................................................................................... 2A14
8-4. Propeller Blade Minor Repair ........................................................................................... 2A16
8-5. Propeller Governor............................................................................................................ 2A17
8-6. Engine Installation............................................................................................................. 2A20
8-7. Schematic Diagram of Turbocharger System.................................................................... 2A23
8-8. Induction System Installation............................................................................................ 2B5
8-8a. Magneto Assembly............................................................................................................ 2B7
8-9. Contact Spring Inspection ................................................................................................. 2B8
8-10. Contact Points.................................................................................................................... 2B9
8-11. Impulse Coupling .............................................................................................................. 2B10
8-12. Flyweight Clearance of Impulse Coupling........................................................................ 2B10
8-13. Rotor Holding Tool Installed............................................................................................. 2B11
8-14. Timing Kit Installed........................................................................................................... 2B11
8-15. Cast-In Timing Marks........................................................................................................ 2B12
8-16. Fabricated Pointer.............................................................................................................. 2B12
8-17. Engine Timing Marks........................................................................................................ 2B13
8-18. Removing Spring From Lead Assembly........................................................................... 2B15
8-19. Assembly Tool................................................................................................................... 2B17
8-20. Assembly Tool Application............................................................................................... 2B17
8-21. Measuring Lead Assembly Length.................................................................................... 2B17
8-22. Ferrule Seating Tool.......................................................................................................... 2B19
8-23. Measuring Wire From Top of Ferrule ............................................................................... 2B19
8-24. Needle................................................................................................................................ 2B19
8-25. Installing Grommet Over Lead Assemblies...................................................................... 2B19
8-26. Lead Assembly Installed in Grommet............................................................................... 2B20
8-27. Wire Doubled Over For Installation of Eyelet .................................................................. 2B20
8-28. Ignition Schematic............................................................................................................. 2B21
8-29. Removing Frozen Spark Plug............................................................................................ 2B23
8-30. Lubrication System Maintenance Points........................................................................... 2B24
8-31. Schematic Diagram of Fuel Injection System................................................................... 2C2
8-32. Fuel Injection Nozzle Assembly ....................................................................................... 2C3
8-33. Engine Controls................................................................................................................. 2C4
8-34. Idle Speed and Mixture Adjustment Points....................................................................... 2C6
8-35. Sectional View of Altitude Compensating Fuel Pump Assembly..................................... 2C8
8-36. Exhaust Bypass Screw....................................................................................................... 2C10
8A-l. Propeller Installation (Hartzell)......................................................................................... 2C21
8A-2. Propeller Blade Minor Repair ........................................................................................... 2C22
8A-3. Propeller Governor............................................................................................................ 2C24
8A-3a. Engine Cowling Installation.............................................................................................. 2D2
8A-4. Engine Installation (PA-28R-201)..................................................................................... 2D4
8A-4a. Adjustment of Engine Controls......................................................................................... 2D7
8A-5. Fuel Injector....................................................................................................................... 2D8
8A-6. Schematic Diagram of RSA Injector System.................................................................... 2D9
Interim Revision: 2/21/95
1A7
To Next Page
Loading...
Need help?
General