LIST OF ILLUSTRATIONS (CONT)
Aerofiche
Figure Grid No.
8A-7. Fuel-Air Bleed Nozzle....................................................................................................... 2D11
8A-8. Contact Points.................................................................................................................... 2D13
8A-9. Rotor Holding Tool Installed............................................................................................. 2D14
8A-10. Timing Kit Installed........................................................................................................... 2D14
8A-11. Aligning Timing Marks..................................................................................................... 2D15
8A-12. Checking Flyweight Clearance of Impulse Coupling ....................................................... 2D15
8A-13. Engine Timing Marks........................................................................................................ 2D17
8A-14. Magneto Adjustment Limits.............................................................................................. 2D17
8A-15. Magneto Timing Mark....................................................................................................... 2D18
8A-16. Removing Spring From Lead Assembly........................................................................... 2D18
8A-17. Assembly Tool................................................................................................................... 2D19
8A-18. Using Assembly Tool........................................................................................................ 2D19
8A-19. Measuring Lead Assembly Length.................................................................................... 2D19
8A-20. Cutting Metallic Braid From End of Lead ........................................................................ 2D21
8A-21. Unbraiding Metallic Shielding.......................................................................................... 2D21
8A-22. Forming Shielding Around Ferrule................................................................................... 2D21
8A-23. Ferrule Seating Tool.......................................................................................................... 2D21
8A-24. Needle................................................................................................................................ 2D21
8A-25. Measuring Wire From Top of Ferrule ............................................................................... 2D23
8A-26. Installing Grommet Over Lead Assemblies ...................................................................... 2D23
8A-27. Lead Assembly Installed in Grommet............................................................................... 2D23
8A-28. Wire Doubled Over For Installation of Eyelet .................................................................. 2D23
8A-29. Removing Spark Plug Frozen to Bushing ......................................................................... 2E1
9-1. Fuel System Diagram (PA-28R-201)................................................................................. 2E11
9-1a. Fuel System Diagram (PA-28R-201 S/N’s 37001 and up)................................................ 2E12
9-2. Fuel System Diagram (PA-28R-201T).............................................................................. 2E13
9-3. Fuel Sender Units Installation........................................................................................... 2E15
9-4. Engine Primer System Placard.......................................................................................... 2E16
9-5. Fuel Quantity Indicator...................................................................................................... 2E19
9-6. Fuel Filter Bowl and Screen.............................................................................................. 2E20
9-7. Fuel Pump Variable Resistor............................................................................................. 2E21
9-8. Tolerance, Union Nut and Tubing..................................................................................... 2F2
10-1. Instrument Panel (Typical)................................................................................................ 2F11
10-1a. Instrument Panel(PA-28R-201 S/N’s 2837001 and up)..................................................... 2F12
10-1b. Instrument Panel (PA-28R-201T S/N’s 2803001 and up)................................................. 2F13
10-2. Pitot Static System............................................................................................................. 2F14
10-3. Vacuum-Auxiliary Vacuum System .................................................................................. 2F16
11-2. Lamp-Bank Load............................................................................................................... 2G20
11-3. Checking Field Circuit ...................................................................................................... 2G21
11-4. Testing Field Circuit.......................................................................................................... 2G21
11-5. Testing Rectifiers (Positive).............................................................................................. 2G22
11-6. Testing Rectifiers (Negative)............................................................................................. 2G23
11-7. C-3928 Fixtures and Adapters........................................................................................... 2G24
11-8. Removing Rectifiers.......................................................................................................... 2G24
11-9. Installing Rectifiers ........................................................................................................... 2H1
11-10. Soldering Rectifiers Lead.................................................................................................. 2H2
11-11. Testing Stator Coils........................................................................................................... 2H3
11-12. Removing End Bearing ..................................................................................................... 2H4
Revised: 2/13/89
1A8
To Next Page
Loading...
Need help?
General