What to do if PROEMION CANlink wireless 3002 does not transmit CAN messages?
If the PROEMION Network Hardware device does not transmit any CAN messages, verify the CAN baud rate, the wiring, and the CAN bus termination resistors. Also, check the CAN message filter settings in the configuration and ensure that the checkbox 'Start CAN message output on wireless side after link is established' in the Advanced Settings ¬ tab Expert is enabled.
How to check power supply of PROEMION CANlink wireless 3002 Network Hardware?
If the PROEMION Network Hardware device is without any function, check the power supply via the CAN connector.
What to do if PROEMION Network Hardware does not receive CAN messages?
If the PROEMION Network Hardware device does not receive CAN messages, check the CAN connection and the configuration of the CAN messages and filters. Also, check if the CAB bus termination resistor is correctly installed.
Why does PROEMION CANlink wireless 3002 Network Hardware LED light up constant red?
If the LED on the PROEMION Network Hardware lights up constant red, this could be due to a CAN error (e.g., bus off), a radio module error, or a critical voltage issue.
What to do if PROEMION CANlink wireless 3002 does not transmit all CAN messages?
If the PROEMION Network Hardware device does not transmit all CAN messages, verify that the CANopen stack is enabled. You may also need to change the CAN identifiers of the affected CAN messages (RX SDOs, TX SDOs, emergency messages).
What to do if PROEMION CANlink wireless 3002 Network Hardware LED lights up constant red after powering on?
If the LED lights up constant red on the PROEMION Network Hardware after powering on, ensure that "Enable boot-up message" is disabled in the device configuration.
What to do if PROEMION CANlink wireless 3002 is stuck in sleep mode?
If the PROEMION Network Hardware device is stuck in sleep mode, check if terminal 15 is connected or VCC is connected to pin 3 of the CAN / Power connector. For testing, use the CAN cable M12 5-pin/D-Sub/Power terminal 15 ON from the starter kit.
Why is the PROEMION Network Hardware LED light constant red?
A constant red LED on your PROEMION Network Hardware indicates a CAN error (such as bus off), a radio module error, or a critical voltage issue.
Specifies the intended applications and safety warnings for the device's operation.
Provides critical safety warnings, including DANGER, WARNING, and CAUTION levels.
Instructions for installing the necessary software for the CANlink wireless device.
Guides on how to connect the device, including CAN, power, and PC connections.
Step-by-step guide for connecting the device to a PC using the RS232 interface for configuration.
Describes how to configure and perform function tests for the CAN-Bluetooth Interface.
Guides on configuring the CAN-Bluetooth Interface for wireless data transmission.
Guides on performing a function test for the CAN-Bluetooth Interface using test messages.
Explains how to configure and test the CAN-CAN-Bluetooth Bridge functionality.
Guides for configuring the CAN-CAN-Bluetooth Bridge as a slave and master device.
Details on performing a function test for the CAN-CAN-Bluetooth Bridge.
Describes how to configure and operate the CAN-WLAN Interface for wireless data.
Guides on configuring the CAN-WLAN Interface for network integration.
Guides on performing a function test for the CAN-WLAN Interface.
Explains configuration for the CAN-CAN-WLAN Bridge for wireless CAN bus systems.
Guides for configuring the CAN-CAN-WLAN Bridge as slave and master devices.
Details on performing a function test for the CAN-CAN-WLAN Bridge.
Guides on using the CANlink wireless Configurator for device setup.
Provides information on how to use and configure CAN functions, including CANopen.
Explains how to set up message filters to manage CAN data transmission.
Instructions for updating the device firmware using the RS232 interface.
Step-by-step guide to perform a firmware update using RMtools Firmware Programmer.
General| Category | Network Hardware |
|---|---|
| Model | CANlink wireless 3002 |
| Operating Temperature | -40°C to +85°C |
| Enclosure | IP67 |
| Data Logging | Yes |
| Interfaces | CAN |
| Wireless | UMTS |
| Protocols | CAN, J1939 |
To Next Page
