PVA PVA2000 - User Manual

Using The Electronic Manual
Requirements
The following is a list of system requirements for the electronic manual:
 Pentium Processor
 64 MB of RAM
 50 MB of Available Hard Drive Space
 Windows
®
98 SE, Millenium, NT, 2000, or XP Operating System
 CD-ROM Drive
 800 x 600 Screen Resolution
 AutoCAD
®
or Volo™ View 2000-129 (Volo™ View is provided on CD)
 Adobe
®
Acrobat
®
or Acrobat
®
Reader (Acrobat
®
Reader is provided on CD)
Opening the Manual
To open the electronic manual, insert the manual CD into your CD-ROM drive. The manual startup menu will
appear. If this is the first time the manual has been used, a disclaimer will have to be acknowledged. If your CD-
ROM drive is not configured to Auto Run, open Windows Explorer
®
and open ‘Startupmenu.exe’.
Navigation
Navigating the electronic manual can be done by clicking on a topic in the left pane. Several of the topics have
sub-topics which can be accesses by clicking on the [+] symbol to the left of the parent topic. The table of
contents also has links to specific areas of the manual. To search for a specific topic, use the find function by
keying ‘CTRL+F’.
Viewing Documents
The electronic manual uses external documentation for schematics, custom equipment documentation, etc. To
view these documents, click the link to the specified topic. If the topic is located on an external document, there
will be a button to access these documents. When you click the button, Adobe
®
may display a confirmation
message asking if you want to launch the application used to view the document. Select All, and a list of
available documents on that topic will appear. Click the document you wish to view. To return from an external
document, click on the back arrow for PDF documents. Close the AutoCAD
®
viewer to return from viewing a
schematic. All schematics are in a *.dwg format, and all other external documents are in *.pdf format. A
compatible viewer for each type of document is required to run the electronic manual.
Troubleshooting
If you have a problem with the electronic manual, check the following:
• The electronic manual was started using the ‘Startupmenu.exe’ file.
• The electronic manual disclaimer has been acknowledged.
• There is an AutoCAD
®
compatible viewer installed.
• There is a Portable Document Format compatible viewer installed (PDF Viewer).
• The original directory structure has not changed.
If everything in the above list checks out and you are still having problems with the electronic manual, uninstall
Adobe
®
Acrobat
®
(or Adobe
®
Reader), and AutoCAD
®
(or Volo™ View), then reinstall each.

Summary

Using The Electronic Manual

Requirements

System requirements for the electronic manual.

Opening the Manual

Steps to open the electronic manual from the CD-ROM.

Navigation

How to navigate topics and use the find function.

Viewing Documents

How to view external documents like schematics and PDFs.

Troubleshooting

Common issues and solutions for the electronic manual.

Disclaimer

Configuration

Machine Specifics

Details about the machine's serial number, revision, and version.

Power Requirements

Specifications for electrical power needed by the machine.

Pressure Settings

Table detailing pressure settings for various regulators.

Optional Equipment

Operation and Maintenance Manual

Preface

Introduction to the manual, including notice and revisions.

Content of This Manual

Overview of manual sections: Intro, Install, Safety, Operation.

Introduction

Overview of the workcell's design and applications.

Installation and Setup

Steps for connecting the machine to power and air.

Operating Safety

Safety features protecting the operator during operation.

Operation

Steps to check and initiate machine startup.

Fault Recovery

Procedure to return machine to Cycle Stop after errors.

Troubleshooting

Information and steps for contacting technical support.

Controller Management

Resets the Galil controller to factory defaults.

System Checks and Maintenance

Steps to check AC and DC voltages in the enclosure.

Maintenance

Schedule for routine maintenance tasks.

Procedures

Step-by-step procedure for replacing conveyor belts.

Appendices

Appendix A: Definitions

Glossary of terms used in the manual.

Appendix B: Serial Communication

Information on RS-232 communication between PC and workcell.

Appendix C: Error Codes

List of DMC motion controller error codes.

Appendix D: Velocity Settings

Maximum speed settings for open loop stepper systems.

Appendix E: Wiring Legend

Legend for wire numbering and color coding.

PVA PVA2000 Specifications

General

Brand	PVA
Model	PVA2000
Category	Paint Sprayer
Language	English