Renesas RL78/G13 User Manual

RL78/G13 CHAPTER 12 SERIAL ARRAY UNIT
R01UH0146EJ0100 Rev.1.00 697
Sep 22, 2011
Table 12-4. Selection of Operation Clock For Simplified I
2
C
SMRmn
Register
SPSm Register Operation Clock (fMCK)
Note
CKSmn PRS
m13
PRS
m12
PRS
m11
PRS
m10
PRS
m03
PRS
m02
PRS
m01
PRS
m00
fCLK = 32 MHz
X X X X 0 0 0 0 fCLK 32 MHz
X X X X 0 0 0 1 fCLK/2 16 MHz
X X X X 0 0 1 0 fCLK/2
2
8 MHz
X X X X 0 0 1 1 fCLK/2
3
4 MHz
X X X X 0 1 0 0 fCLK/2
4
2 MHz
X X X X 0 1 0 1 fCLK/2
5
1 MHz
X X X X 0 1 1 0 fCLK/2
6
500 kHz
X X X X 0 1 1 1 fCLK/2
7
250 kHz
X X X X 1 0 0 0 fCLK/2
8
125 kHz
X X X X 1 0 0 1 fCLK/2
9
62.5 kHz
X X X X 1 0 1 0 fCLK/2
10
31.25 kHz
0
X X X X 1 0 1 1 f
CLK/2
11
15.63 kHz
0 0 0 0 X X X X fCLK 32 MHz
0 0 0 1 X X X X fCLK/2 16 MHz
0 0 1 0 X X X X fCLK/2
2
8 MHz
0 0 1 1 X X X X fCLK/2
3
4 MHz
0 1 0 0 X X X X fCLK/2
4
2 MHz
0 1 0 1 X X X X fCLK/2
5
1 MHz
0 1 1 0 X X X X fCLK/2
6
500 kHz
0 1 1 1 X X X X fCLK/2
7
250 kHz
1 0 0 0 X X X X fCLK/2
8
125 kHz
1 0 0 1 X X X X fCLK/2
9
62.5 kHz
1 0 1 0 X X X X fCLK/2
10
31.25 kHz
1
1 0 1 1 X X X X f
CLK/2
11
15.63 kHz
Other than above Setting prohibited
Note When changing the clock selected for fCLK (by changing the system clock control register (CKC) value), do so
after having stopped (serial channel stop register m (STm) = 000FH) the operation of the serial array unit
(SAU).
Remarks 1. X: Don’t care
2. m: Unit number (m = 0, 1), n: Channel number (n = 0 to 3), mn = 00 to 03, 10 to 13
Here is an example of setting an I
2
C transfer rate where fMCK = fCLK = 32 MHz.
fCLK = 32 MHz
I
2
C Transfer Mode
(Desired Transfer Rate)
Operation Clock (f
MCK) SDRmn[15:9] Calculated
Transfer Rate
Error from Desired Transfer
Rate
100 kHz fCLK/2 79 100 kHz 0.0%
400 kHz fCLK 39 400 kHz 0.0%
1 MHz fCLK/2 7 1 MHz 0.0%

Renesas RL78/G13 Specifications

General

Brand	Renesas
Model	RL78/G13
Category	Computer Hardware
Language	English