Renkforce RF2000 v2 Series - Page 67

110 pages

Save Page as PDF

To Next Page

To Previous Page

Here, the extruders can be assigned. For example, it is possible to use one of the two extruders for "Inll" only.

The extrusion width for all the different print versions can be set here. The extrusion width is the width of the output plastic thread. E.g., this may

beincreasedattherstlayer,sothatthebottomoftheprintedobjectbecomesdenser.

Main Page

Default Chapter2
- Table of Contents2
1 Introduction4
2 Explanation of Symbols4
3 Intended Use5
4 Scope of Delivery6
- A) RF2000 V2 Finished Device (Single and Dual Extruder) (FGS and FGD)6
- B) RF2000 V2 Construction Kit (Single Extruder) (BSS)6
5 Important Advice and Notes - Please Read7
6 Safety Notes8
- A) General Information8
- B) Set-Up, Site of Operation8
- C) Operation9
- D) Socket9
7 Feature Description10
8 Working Principle of the 3D Printer10
9 Overview of the most Important Parts11
- A) Single Extruder11
- B) Dual Extruder12
10 Required Tools and Material13
11 First Commissioning14
- A) Overview Of The First Steps14
- B) Installation Of The Filament Holder15
- C) Inspection of the Fan Sheet and the Actuation for the Z-Limit Switch17
- D) Setup and Transport18
- E) Mains Connection And First Activation18
12 Software And Firmware Installation19
- A) Download And Unpacking Of The Software/Firmware Package19
- B) General Information on the Repetier-Host Software19
- C) Installation of the Repetier-Host Software20
- D) Updating Of The Firmware20
13 Operation at the Printer21
- A) Description of the Main Display21
- B) Function Description of the Operating Buttons22
- C) Description of the Extruders22
- D) the Expanded Main Menu23
- E) Menu Overview23
- F) Functions of the Individual Menu Items26
14 Calibration29
- A) Overview of Calibration29
- B) General Notes on Calibration29
- C) Setting the Distance between the Nozzle and the Printing Plate31
- D) Executing the Head Bed Scan for PLA or ABS36
- E) Executing the Quick Head Bed Scan39
15 Inserting, Removing And Changing The Filament42
- A) Inserting The Filament - Mechanical Part42
- B) Inserting The Filament Via The Printer Menu43
- C) Removing And Changing The Filament45
16 First Print of an Example Object from the SD Card46
17 General Notes on 3D Printing48
18 Software "Repetier-Host49
- A) Connection of the Connected Printer49
- B) Manual Operation Via the Software51
- C) Placement of a Printing Object in the Software52
- D) Preparation for Print56
- E) Print60
- F) more Detailed Description of the Slicer Functions63
- G) Setting up Another Slic3R Version73
19 Extended Calibration77
- A) Determining the Highest Position of the Printing Plate77
- B) Fine Adjustment Of The Filament Infeed81
- C) Fine Adjustment of the Two Extruders84
- D) Correction of the Printing Plate Temperature86
20 Firmware Update with the Arduino87
- Tm Ide87
21 Maintenance91
- A) General Information91
- B) Cleaning91
- C) Fuse Replacement92
- D) Checking the Belt Tension93
- E) Nozzle Change95
22 Troubleshooting96
23 Handling99
24 Disposal99
25 Technical Data99
26 Annex100
- A) Wiring Plan100
- B) Setting up the Printer Settings102
- C) Status and Error Messages105

Related product manuals

RF500 Maker Construction Kit

149 pages

Renkforce RF2000 v2 Series - Page 67

Table of Contents

Related product manuals