Renkforce RF2000 v2 Series

To Next Page

To Previous Page

(1) Thenoteseldmaycontainimportantinformationontheslicersetting.Thismayalsocontaininformationonthelamentswithwhichthis

setting was tested or compiled.

If there is a note here, it only applies to the this slicer setting, e.g. to "PLA175_200_04".

Pleasealsoobservethenoteeldsinthetabs"Filament Settings" and "Printer Settings".

Click the menu "Settings" (1) in the slicer window and open the item "Filament Settings..." (2).

Main Page

Default Chapter2
- Table of Contents2
1 Introduction4
2 Explanation of Symbols4
3 Intended Use5
4 Scope of Delivery6
- A) RF2000 V2 Finished Device (Single and Dual Extruder) (FGS and FGD)6
- B) RF2000 V2 Construction Kit (Single Extruder) (BSS)6
5 Important Advice and Notes - Please Read7
6 Safety Notes8
- A) General Information8
- B) Set-Up, Site of Operation8
- C) Operation9
- D) Socket9
7 Feature Description10
8 Working Principle of the 3D Printer10
9 Overview of the most Important Parts11
- A) Single Extruder11
- B) Dual Extruder12
10 Required Tools and Material13
11 First Commissioning14
- A) Overview Of The First Steps14
- B) Installation Of The Filament Holder15
- C) Inspection of the Fan Sheet and the Actuation for the Z-Limit Switch17
- D) Setup and Transport18
- E) Mains Connection And First Activation18
12 Software And Firmware Installation19
- A) Download And Unpacking Of The Software/Firmware Package19
- B) General Information on the Repetier-Host Software19
- C) Installation of the Repetier-Host Software20
- D) Updating Of The Firmware20
13 Operation at the Printer21
- A) Description of the Main Display21
- B) Function Description of the Operating Buttons22
- C) Description of the Extruders22
- D) the Expanded Main Menu23
- E) Menu Overview23
- F) Functions of the Individual Menu Items26
14 Calibration29
- A) Overview of Calibration29
- B) General Notes on Calibration29
- C) Setting the Distance between the Nozzle and the Printing Plate31
- D) Executing the Head Bed Scan for PLA or ABS36
- E) Executing the Quick Head Bed Scan39
15 Inserting, Removing And Changing The Filament42
- A) Inserting The Filament - Mechanical Part42
- B) Inserting The Filament Via The Printer Menu43
- C) Removing And Changing The Filament45
16 First Print of an Example Object from the SD Card46
17 General Notes on 3D Printing48
18 Software "Repetier-Host49
- A) Connection of the Connected Printer49
- B) Manual Operation Via the Software51
- C) Placement of a Printing Object in the Software52
- D) Preparation for Print56
- E) Print60
- F) more Detailed Description of the Slicer Functions63
- G) Setting up Another Slic3R Version73
19 Extended Calibration77
- A) Determining the Highest Position of the Printing Plate77
- B) Fine Adjustment Of The Filament Infeed81
- C) Fine Adjustment of the Two Extruders84
- D) Correction of the Printing Plate Temperature86
20 Firmware Update with the Arduino87
- Tm Ide87
21 Maintenance91
- A) General Information91
- B) Cleaning91
- C) Fuse Replacement92
- D) Checking the Belt Tension93
- E) Nozzle Change95
22 Troubleshooting96
23 Handling99
24 Disposal99
25 Technical Data99
26 Annex100
- A) Wiring Plan100
- B) Setting up the Printer Settings102
- C) Status and Error Messages105

Renkforce RF2000 v2 Series - Page 68

Table of Contents

Related product manuals