Rockwell Automation Publication 2711R-UM001H-EN-E - April 2021 99
Chapter 6 Troubleshoot the System
Alert 2023 Application has been left in edit or test mode.
Reconnect the designer or press OK to proceed to the configuration
screens.
Alert 2024 File not found. Verify the location of the file and try again.
Recipe 2025 Copy failed. Only existing recipe files can be updated.
Create the recipe through the designer or rename this recipe to the
existing recipe name and try again.
Recipe 2026 Copy failed. Invalid recipe file.
The imported recipe must have the same number of ingredients and
data sets as the existing recipe it is replacing.
Alarm 2027 Alarm logs can only be copied from a loaded application. Load the application into Edit, Test, or Run mode and retry.
Alert 2028
Files can only be copied to a secured application while editing the
application.
The application has been secured with design rights. Load the
application into Edit mode and retry.
Alert 2029
Files can only be copied from a secured application while editing
the application.
The application has been secured with design rights. Load the
application into Edit mode and retry.
Alert 2030 Cannot delete a loaded application. Unload application and try again.
Alert 2031
Files can only be deleted from a secured application while editing
the application.
The application has been secured with design rights. Load the
application into Edit mode and retry.
Alert 2032 Return to out of box condition?
Press Yes to reboot the terminal and return to the out of box
condition.
Alert 2033 Source file does not exist. Make sure the source file exists and retry.
Alert 2034 Destination folder does not exist. Make sure the destination location exists and retry.
Alert 2035 Insufficient disk space. Free disk space and try again.
Remove files to free space by pressing the Delete File button on the
File Transfer tab.
Alert 2036
This application is not validated. Are you sure you want to run a
non-validated application?
Press Yes to continue running the invalid application, or No to
proceed to the configuration screens. Then, edit and validate the
application. Correct all validation errors, save the application, and try
again.
Aler 2037
This application is invalid. Continue setting as startup
application?
Press Yes to continue setting the invalid application as a startup
application, or No to proceed to the configuration screens. Then, edit
and validate the application. Correct all validation errors, save the
application, and try again.
Alert 2038
Cannot change password because password has been marked as
unmodifiable.
Edit the application and go to the Security tab. Check the Modifiable?
box associated with the username and password.
Alert 2039
Cannot change password because no user is logged onto the
terminal.
Log on as one of the users defined in the application and retry.
Alert 2040 Old password does not match the password for the current user. Enter the current user’s password for the Old Password.
Alert 2041 Cannot reset password, this is an unknown user. Log on as one of the users defined in the application and retry.
Alert 2042
Cannot change password, new and confirm passwords don't
match.
Verify the new password matches the confirmed password and
retry.
Alert 2043 Access Denied
The username/password is either incorrect or the user does not
have the access right for the associated screen.
Alert 2044 Cannot run application while in Safe mode. Reboot the terminal to exit Safe mode and retry.
Alert 2045 Cannot run applications from external storage. Copy or save to internal storage and try again.
Alert 2046 Passwords cannot be modified while in test mode.
The change password and reset password devices are only enabled
while in Run mode.
Alert 2047 File is read-only. Continue? Choosing to continue will overwrite the read-only file.
Alert 2048 Application has been modified. Continue?
Edit the application and save prior to performing this operation,
otherwise changes to the application may be lost.
Alert 2049 Allow firmware update? Press Yes to continue with the firmware update.
Alert 2050 The value is not within the minimum and maximum range.
Enter a value within the allowable range. If you do not know the
range Edit the application to determine the allowable range for the
device.
Alert 2051 Allow Autorun? Press No to disallow Autorun.
Alert 2052 Application has been modified. Allow Autorun?
Press No to disallow Autorun. Edit the application and save prior to
performing this operation, otherwise changes to the application may
be lost.
Alert 2053 Screen switching controlled by external source.
Screen navigation devices are disabled if the screen has been
changed to via controller.
Alert 2054 Cannot reset the terminal in Safe mode.
Terminal reboot is disabled on the emulator. Select Flash>Save and
then select File>Reset>Hard to reboot the emulator.
Alert 2055 Image exceeds maximum resolution of 800x800. Open file in image editor and reduce the resolution.
PanelView 800 Terminal Alerts (Continued)
Category ID Description Corrective Action
To Next Page
Loading...
Need help?
General
