When the “EFFECTS” indicator is lit
fig.5-5-6TEXT
1: Reverb Level (p. 102)
2: Delay Level (p. 104)
3: Multi-Effects Control 1 (p. 107)
4: Multi-Effects Control 2 (p. 107)
5: Multi-Effects Control 3 (p. 106)
6, 7: Determined by the [FILTER/AMP/PITCH] status
* During Patch Edit, it is not possible to access the editing
page for the effect parameters.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Accessing only the editing page without modi-
fying the setting value
If you wish to see the current setting before you make
any changes, hold down [SHIFT] while you operate
the knob, and you will access only the editing page
without modifying the value.
Maintaining the relative difference between
tones when editing
In an editing page, you can use [INC] [DEC] or the
[VALUE] dial to edit while preserving the relative dif-
ference between tones. Use this method when appro-
priate.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
The patch edit page will show the currently selected
patch parameters and the settings of each tone.
fig.5-2TEXT
During patch editing, the BANK [1]–[8] indicators will
show the following status.
fig.5-4
Turning each tone on/off (Tone Switch)
Of the tones which make up a patch, tones whose but-
ton indicator is lit are turned ON. You can press the
button to switch each tone on/off.
Selecting the tone for editing (Tone
Select)
The tone with a lit button indicator will be affected by
your editing.
The tone to which your editing will apply is indicated
by “ ” shown at the left of the value. In the following
illustration, TONE 1 is being edited.
fig.5-5
Press a button BANK [5]–[8] to select the tone that you
wish to edit.
The indicator of the selected button will light, and “ ”
will be displayed at the left of the setting value.
You can select two or more tones by holding down
one of the buttons while you press another button.
6. To exit the editing pages, press [EDIT] or
[EXIT].
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
An asterisk “*” will be displayed at the left of the
Group of an edited patch. This indicates that the set-
tings of this patch have been modified.
If you select a different patch when the “*” is dis-
played, the modified settings will be lost. If you wish
to keep the edited patch, you must perform the Patch
Write operation.
☞ “Saving Patches You’ve Created (Patch
Write) “ (p. 82)
fig.5-3
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
To Next Page
Loading...
