●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
If you use two tones and set a Bias Direction of “UPR”
for one and “LWR” for the other, the two tones will
fade smoothly into each other as you play across the
Bias Point. (This is known as “key crossfade.”)
fig.5-44 (=MC fig.3-43)
By setting Bias Direction to “L&U,” you can create
sounds that are heard only in a specific area of the
keyboard.
fig.5-45 (=MC fig.3-44)
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Tone Pan
This is the setting page for “Adjusting the pan for each
tone (Tone Pan)” (p. 67).
Pan KF (Pan Key Follow)
This parameter causes the stereo location to change
according to the key that is played.
fig.5-46TEXT (=MC fig.3-46)
Range: -100–+100
With positive (+) settings, the sound will move toward
the right as you play higher notes. With negative (-)
settings, the sound will move toward the left as you
play higher notes.
Rnd Pan SW (Random Pan Switch)
This is the setting page for “Causing pan to change
randomly (Random Pan Switch)” (p. 67).
Alt Pan Dpth (Alternate Pan Depth)
This parameter causes the stereo location of the sound
to alternate between left and right each time a note is
played.
Range: L63–63R
When this parameter is set in the L direction, the
sound will alternate in the order of left → right →
left→ right. When set in the R direction, the sound will
alternate in the order of right → left→ right→ left.
Higher settings will cause greater change.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
By using two tones and setting the Alternate Pan
Depth of one to “L63” and of the other to “R63,” you
can make the two tones switch places alternately.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Velo Curve (Amplifier Envelope
Velocity Curve)
Select the curve at which the strength of your playing
on the keyboard will affect the depth of the amplifier
envelope.
Range: 1–7
fig.5-50 (=MC fig.3-36)
Velo Sens (Amplifier Envelope Velocity
Sensitivity)
Specifies how the depth of the amplifier envelope will be
affected by the strength of your playing on the keyboard.
Range: -100–+150
With positive (+) settings, the volume will increase as
you play more strongly on the keyboard. With nega-
tive (-) settings, the volume will decrease as you play
more strongly on the keyboard. If this is set to “0,” the
volume will not be affected by the strength of your
playing on the keyboard.
If you wish to change the loudness of notes
played on the keyboard...
☞ “Changing the Loudness of Notes Played on
the Keyboard (Keyboard Velocity)” (p. 163)
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
If velocity sensitivity is set to a positive (+) value, the
volume will be loud when you play strongly and soft
when you play softly. As this value is increased, the
volume difference between strongly played and softly
played notes will gradually increase.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
The four front panel knobs [ATTACK] / [DECAY] /
[SUSTAIN] / [RELEASE] can be used to set the most
common-used parameters of the amplifier envelope,
To Next Page
Loading...
