Satec PM130E - Page 158

To Next Page

To Previous Page

Appendix E Billing/TOU P R O F I L E L O G F I L E

158 PM130 PLUS Powermeter Series

The number of parameters in each section is automatically configured depending

on the number of actual tariffs you defined in the TOU Daily Profiles.

Main Page

Default Chapter9
- Table of Contents9
Chapter 1 General Information12
Features12
Available Options14
- Digital I/O15
- Analog Output15
- Additional Communication Port - COM215
- TOU - Battery-Operated Clock Unit15
Customized Options16
- Device Resolution16
- Energy Rollover16
- Display Options16
Measured Parameters16
Chapter 2 Installation19
Site Requirements19
Package Contents19
Mechanical Installation20
- Panel Mounting21
- DIN Rail Mounting21
Electrical Installation23
- Typical Installation23
- Terminals24
- Power Source Connection24
- Voltage Input Connection25
- Current Input Connection25
- Wiring Diagrams26
I/O Connections33
- 4DI/2DO Module33
- DI Module35
- 12DI/4RO Module35
- 4AO Module - Analog Outputs37
- TOU Module - RTC and 4 Digital Inputs38
Communications Connections39
- COM1 RS-485 Connection40
- ETH Module - COM2 Ethernet Connection41
- PRO Module - COM2 PROFIBUS Connection42
- RS-232/422-485 Module - COM2 Connection43
- Connecting a GSM/GPRS Modem45
Chapter 3 Using Front Display46
Indicators and Controls46
- Device Diagnostics46
- Numeric LED Display46
- Load Bar Graph47
- Energy Pulse LED47
- Port Activity Leds47
- Navigation Buttons47
Data Display47
- Display Features47
- Navigation Buttons49
- Simple Reset of Accumulated Data49
- Common Measurements Display50
- Min/Max and Maximum Demand Display51
- Harmonics Display (PM130EH)52
- Energy Display (PM130E/EH)53
Status Display54
- Pulse and Time Counters56
- Alarm Display56
- Diagnostics Display56
Using the Menus57
- Navigation Buttons57
- Selecting Menus57
- Entering the Password58
- Selecting a Menu Entry59
- Viewing and Changing Setup Options59
Chapter 4 Using PAS Software61
Installing PAS61
Creating a New Site for Your Meter61
Setting up Communications63
- Communicating through a Serial Port63
- Communicating through the Internet64
Setting up the Meter65
- Preparing Setups for the Meter65
- Downloading Setups to the Meter66
- Uploading Setups from the Meter66
  - Authorization67
Chapter 5 Configuring the PM130 PLUS68
Configuring Communications68
- Setting up Serial Communication Ports68
- Setting up Ethernet69
- Setting up GPRS Network71
- Setting up Expertpower Client72
- Setting up TCP Notification Client73
General Meter Setup75
- Basic Meter Setup75
- Device Options77
- Configuring Digital Inputs79
- Configuring Relay Outputs81
- Configuring Analog Outputs83
- Configuring Counters85
- Configuring Alarm/Control Setpoints87
- Configuring the Display90
- Local Time Settings91
Configuring Meter Security93
Configuring Billing/Tou95
- Configuring Billing/Tariff Registers95
- Configuring the Daily Tariff Schedule97
- Configuring the Season Tariff Schedule97
Configuring Recorders99
- Configuring Meter Memory99
- Configuring the Event Recorder101
- Configuring the Data Recorder101
Configuring Communication Protocols105
- Configuring Modbus105
- Configuring DNP3106
Chapter 6 Device Control and Upgrading109
Resetting Accumulators, Maximum Values and Files109
Updating the Meter Clock110
Viewing and Clearing Device Diagnostics112
Viewing Communication Status and Statistics112
Remote Relay Control113
- Upgrading Device Firmware114
Chapter 7 Monitoring Meters116
Viewing Real-Time Data116
Viewing Real-Time Min/Max Log118
Viewing Real-Time Waveforms119
- Viewing Real-Time Harmonic Spectrum121
Chapter 8 Retrieving and Storing Files125
Uploading Files on Demand125
Using the Upload Scheduler126
Viewing Files On-Line128
Exporting Files128
- Exporting Files in COMTRADE and PQDIF Formats128
- Exporting Files in Excel Format130
Chapter 9 Viewing Files131
Operations with Files131
Viewing Options131
- Customizing Views131
- Working with Tables132
- Working with Graphic Windows132
Viewing the Event Log134
- Viewing the Data Log135
Appendix A Technical Specifications136
Appendix B Analog Output Parameters143
Appendix C Setpoint Triggers and Actions145
Appendix D Parameters for Data Monitoring and Logging148
Appendix E Billing/Tou Profile Log File157
Appendix F Data Scales159
Appendix G Device Diagnostic Codes160
Index161

Satec PM130E - Page 158

Table of Contents

Other manuals for Satec PM130E

Related product manuals