Satec PM130E - 2.3 Mechanical Installation

161 pages

To Next Page

To Previous Page

Chapter 2 Installation Mechanical I N S T A L L A T I O N

20 PM130 PLUS Powermeter Series

2.3 Mechanical Installation

Refer to the figures provided in this section to properly perform the

mechanical installation.

Figure 2-1. Dimensions

Main Page

Default Chapter9
- Table of Contents9
Chapter 1 General Information12
Features12
Available Options14
- Digital I/O15
- Analog Output15
- Additional Communication Port - COM215
- TOU - Battery-Operated Clock Unit15
Customized Options16
- Device Resolution16
- Energy Rollover16
- Display Options16
Measured Parameters16
Chapter 2 Installation19
Site Requirements19
Package Contents19
Mechanical Installation20
- Panel Mounting21
- DIN Rail Mounting21
Electrical Installation23
- Typical Installation23
- Terminals24
- Power Source Connection24
- Voltage Input Connection25
- Current Input Connection25
- Wiring Diagrams26
I/O Connections33
- 4DI/2DO Module33
- DI Module35
- 12DI/4RO Module35
- 4AO Module - Analog Outputs37
- TOU Module - RTC and 4 Digital Inputs38
Communications Connections39
- COM1 RS-485 Connection40
- ETH Module - COM2 Ethernet Connection41
- PRO Module - COM2 PROFIBUS Connection42
- RS-232/422-485 Module - COM2 Connection43
- Connecting a GSM/GPRS Modem45
Chapter 3 Using Front Display46
Indicators and Controls46
- Device Diagnostics46
- Numeric LED Display46
- Load Bar Graph47
- Energy Pulse LED47
- Port Activity Leds47
- Navigation Buttons47
Data Display47
- Display Features47
- Navigation Buttons49
- Simple Reset of Accumulated Data49
- Common Measurements Display50
- Min/Max and Maximum Demand Display51
- Harmonics Display (PM130EH)52
- Energy Display (PM130E/EH)53
Status Display54
- Pulse and Time Counters56
- Alarm Display56
- Diagnostics Display56
Using the Menus57
- Navigation Buttons57
- Selecting Menus57
- Entering the Password58
- Selecting a Menu Entry59
- Viewing and Changing Setup Options59
Chapter 4 Using PAS Software61
Installing PAS61
Creating a New Site for Your Meter61
Setting up Communications63
- Communicating through a Serial Port63
- Communicating through the Internet64
Setting up the Meter65
- Preparing Setups for the Meter65
- Downloading Setups to the Meter66
- Uploading Setups from the Meter66
  - Authorization67
Chapter 5 Configuring the PM130 PLUS68
Configuring Communications68
- Setting up Serial Communication Ports68
- Setting up Ethernet69
- Setting up GPRS Network71
- Setting up Expertpower Client72
- Setting up TCP Notification Client73
General Meter Setup75
- Basic Meter Setup75
- Device Options77
- Configuring Digital Inputs79
- Configuring Relay Outputs81
- Configuring Analog Outputs83
- Configuring Counters85
- Configuring Alarm/Control Setpoints87
- Configuring the Display90
- Local Time Settings91
Configuring Meter Security93
Configuring Billing/Tou95
- Configuring Billing/Tariff Registers95
- Configuring the Daily Tariff Schedule97
- Configuring the Season Tariff Schedule97
Configuring Recorders99
- Configuring Meter Memory99
- Configuring the Event Recorder101
- Configuring the Data Recorder101
Configuring Communication Protocols105
- Configuring Modbus105
- Configuring DNP3106
Chapter 6 Device Control and Upgrading109
Resetting Accumulators, Maximum Values and Files109
Updating the Meter Clock110
Viewing and Clearing Device Diagnostics112
Viewing Communication Status and Statistics112
Remote Relay Control113
- Upgrading Device Firmware114
Chapter 7 Monitoring Meters116
Viewing Real-Time Data116
Viewing Real-Time Min/Max Log118
Viewing Real-Time Waveforms119
- Viewing Real-Time Harmonic Spectrum121
Chapter 8 Retrieving and Storing Files125
Uploading Files on Demand125
Using the Upload Scheduler126
Viewing Files On-Line128
Exporting Files128
- Exporting Files in COMTRADE and PQDIF Formats128
- Exporting Files in Excel Format130
Chapter 9 Viewing Files131
Operations with Files131
Viewing Options131
- Customizing Views131
- Working with Tables132
- Working with Graphic Windows132
Viewing the Event Log134
- Viewing the Data Log135
Appendix A Technical Specifications136
Appendix B Analog Output Parameters143
Appendix C Setpoint Triggers and Actions145
Appendix D Parameters for Data Monitoring and Logging148
Appendix E Billing/Tou Profile Log File157
Appendix F Data Scales159
Appendix G Device Diagnostic Codes160
Index161

Satec PM130E - 2.3 Mechanical Installation

Table of Contents

Other manuals for Satec PM130E

Related product manuals