II
F--9999--8 Issue 1
3.3.4 Side Guide Set--Up 3--27...........................................................
3.3.5 Kick Out Solenoid Set--Up 3--28.....................................................
3.3.6 Sheet Hold Down Straps 3--28......................................................
3.3.7 Set Up For Production 3--29........................................................
3.3.8 Run Production 3-- 30..............................................................
3.4 Handwheel and Tab Set-Up 3-34..........................................................
3.4.1 Hand Wheel and Tab Set-Up Definitions 3-35.........................................
HANDWHEEL SET-UPS FOR 5” SHEET WITH 3/16” MARGINS 3-36...............................
HANDWHEEL SET-UPS FOR 6” SHEET WITH 3/16” MARGINS 3-37...............................
HANDWHEEL SET-UPS FOR 7-1/4” SHEET WITH 3/16” MARGINS 3-38...........................
HANDWHEEL SET-UPS FOR 7-1/4” SHEET WITH 1/4” MARGINS 3-39.............................
HANDWHEEL SET-UPS FOR 7-3/4” SHEET WITH 3/16” MARGINS 3-40...........................
HANDWHEEL SET-UPS FOR 7-3/4” SHEET WITH 1/4” MARGINS 3-41.............................
HANDWHEEL SET-UPS FOR 8” SHEET WITH 3/16” MARGINS 3-42...............................
HANDWHEEL SET-UPS FOR 8-1/2” SHEET WITH 3/16” MARGINS 3-43...........................
HANDWHEEL SET-UPS FOR 8-1/2” SHEET WITH 1/4” MARGINS 3-44.............................
HANDWHEEL SET-UPS FOR 8-1/2” SHEET WITH 1/2” MARGINS 3-45.............................
HANDWHEEL SET-UPS FOR 9” SHEET WITH 3/16” MARGINS 3-46...............................
HANDWHEEL SET-UPS FOR 9-1/2” SHEET WITH 3/16” MARGINS 3-47...........................
HANDWHEEL SET-UPS FOR 9-1/2” SHEET WITH 1/4” MARGINS 3-48.............................
HANDWHEEL SET-UPS FOR 9-1/2” SHEET WITH 1/2” MARGINS 3-49.............................
HANDWHEEL SET-UPS FOR 11” SHEET WITH 1/8” MARGINS 3-50...............................
HANDWHEEL SET-UPS FOR 11” SHEET WITH 3/16” MARGINS 3-51..............................
HANDWHEEL SET-UPS FOR 11” SHEET WITH 1/4” MARGINS 3-52...............................
HANDWHEEL SET-UPS FOR 11” SHEET WITH 1/2” MARGINS 3-53...............................
HANDWHEEL SET-UPS FOR 12” SHEET WITH 3/16” MARGINS 3-54..............................
HANDWHEEL SET-UPS FOR 12” SHEET WITH 1/4” MARGINS 3-55...............................
HANDWHEEL SET-UPS FOR 12” SHEET WITH 1/2” MARGINS 3-56...............................
HANDWHEEL SET-UPS FOR 14” SHEET WITH 3/16” MARGINS 3-57..............................
HANDWHEEL SET-UPS FOR 14” SHEET WITH 1/4” MARGINS 3-58...............................
HANDWHEEL SET-UPS FOR 14” SHEET WITH 1/2” MARGINS 3-59...............................
METRIC HANDWHEEL SET-UPS FOR A4 (297mm x 210mm) TAB SIDE: 297 MM MARGIN: 0 MM 3-60
METRIC HANDWHEEL SET-UPS FOR A4 (297mm x 210mm) TAB SIDE: 210 MM MARGIN: 0 MM 3-61
METRIC HANDWHEEL SET-UPS FOR A4 (297mm x 210mm) TAB SIDE: 297 MM MARGIN: 1 MM 3-62
METRIC HANDWHEEL SET-UPS FOR A4 (297mm x 210mm) TAB SIDE: 210 MM MARGIN: 1 MM 3-63
4 MAINTENANCE 4--1......................................................................
4.1 Maintenance 4--3....................................................................
4.1.1 Machine Lubrication 4--3..........................................................
4.1.2 Vacuum Pump Maintenance 4--6...................................................
4.1.3 Machine Timing 4-- 8..............................................................
4.1.4 Preparation for Timing Procedures 4--10..............................................
4.1.5 Timing Procedures 4--11...........................................................
4.1.5.2 Plastic Feed & Cut Operating Arm 4--12..............................................
4.1.6 Reinstall Chains 4-- 15..............................................................
4.2 Calibration 4--16.....................................................................
4.2.1 Preparation for Calibration Procedures 4--16..........................................
4.2.2 Handwheel Settings 4--17..........................................................
4.2.3 Handwheel Calibration Procedures 4--18.............................................
4.2.4 Pile Feeder 4-- 22
..................................................................
To Next Page
Loading...