Siemens SIMOTICS M-1PH8

To Next Page

To Previous Page

Dimension drawings

10.1SIEMENSProductCon󹪝gurator

1PH8 SIMOTICS M main motors

258 Con󹪝guration Manual, 12/2022, A5E51895839A

Main Page

Table of Contents5
Introduction9
About SIMOTICS9
About this Manual9
Content9
Target Group10
Standard Scope10
Websites of Third-Party Companies10
SIMOTICS Documentation10
Documentation in the Internet11
Service and Support12
Siemens Industry Online Support on the Web12
Siemens Industry Online Support on the Road12
Feedback on the Technical Documentation13
Mysupport Documentation14
Technical Support14
Training15
Spare Parts Services15
Important Product Information15
Fundamental Safety Instructions19
General Safety Instructions19
Equipment Damage Due to Electric Fields or Electrostatic Discharge24
Security Information24
Residual Risks of Power Drive Systems25
Motor Description27
Highlights and Benefits27
Technical Characteristics and Environmental Conditions28
Directives and Standards28
Technical Features32
Classifying Environmental Conditions According to Climate Classes35
Derating Factors36
Reduction of the Max. DC-Link Voltage37
Selection and Ordering Data37
Article No. Suffixes for Shaft Height 80 to 16039
Article No. Suffixes for SH 80 Premium Performance42
Article No. Supplements for SH 132 and 160, Synchronous-Reluctance44
Article No. Suffixes for SH 180 to 28046
Article No. Suffixes for SH 28049
Article No. Supplement for Shaft Height 80 to 160 + Holding Brake de52
Article No. Supplement for SH 132 and 160, Synchronous-Reluctance + Holding Brake55
Article No. Supplements for SH 180 to 225 + Holding Brake57
Options58
Rating Plate Data65
Mechanical Properties69
Cooling69
General69
Forced Ventilation69
Water Cooling73
Degree of Protection85
Construction Types87
Types of Bearing88
Drive Output Types and Bearing Versions88
Bearing Lifetime93
NDE Bearings, Insulated Version (Option L27)96
Shaft End98
Mounting of Rotating Unions on 1PH8 Hollow-Shaft Motors98
Rotor-Supported Rotating Union101
Bearingless, Frame-Supported Rotating Union105
Mounting Information and Instructions109
Suggestion for an Adapter for Bearingless, Frame-Supported Rotating Unions112
Radial and Axial Forces113
Radial Force113
Axial Force115
Permissible Radial and Axial Forces for 1PH808 Premium Performance117
Radial and Axial Force Diagrams117
Radial Eccentricity, Concentricity and Axial Eccentricity140
Balancing142
Requirements142
Balancing 1PH8 Motors with "Premium Performance" Bearing Version143
Vibration Response148
Mounting and Mounting Instructions148
Natural Frequency When Mounted150
Misalignment151
Flywheels153
Vibration Stressing153
Vibration Severity Grade156
Noise Emission157
Motor Components and Options159
Motor Components159
Thermal Motor Protection159
Encoder160
Encoder Overview160
Encoder Connection for Motors with a DRIVE-Cliq Interface161
Encoder Connection for Motors Without DRIVE-Cliq (12/17-Pole)162
Encoder Assignment as a Function of Maximum Permissible Speeds162
Incremental Encoder HTL 1024 S/R or HTL 2048 S/R165
Incremental Encoders IC 2048 S/R, in 512 S/R and in 256 S/R167
Absolute Encoder am 2048 S/R170
Options171
Overview of Options171
Sealing Air Connection (Option Q12)171
Protection against Explosion (Options M03 and M39)173
Increased Resistance to Vibration (Option L03)180
Holding Brake (Option)182
Properties182
Mounted Holding Brake for SH 80 to SH 160186
Mounted Holding Brake for SH 180 and SH 225196
Anti-Condensation Heating (Option K45)200
Condensation Drain Hole (Option L12)200
Higher Number of Grounding Terminals in the Terminal Box (Q00)202
Chain of PTC Thermistors for Alarm and Trip (Option A12)202
Configuration205
Configuring Software205
TST Engineering Tool (TIA-Selection-Tool)205
Procedure When Engineering206
SINAMICS Configuring Procedure206
Specifying the Duty Cycle208
Selecting Induction Motors211
Selecting Synchronous Motors212
Selecting Synchronous-Reluctance Motors213
Different Rated Points for Induction Motors214
Configuration for SINAMICS G217
Configuration for 1PH808 Premium Performance218
Technical Data and Characteristics221
Preparing for Use223
Electrical Connection225
Permissible Line System Configurations225
Circuit Diagram of the Motor225
System Integration226
SINAMICS Drive I/O226
Connecting-Up Information227
Routing Cables in a Damp Environment229
Power Connection230
External Fan245
Signal Connection255
Dimension Drawings259
SIEMENS Product Configurator259

Siemens SIMOTICS M-1PH8 - Page 260

Table of Contents

Other manuals for Siemens SIMOTICS M-1PH8

Related product manuals