Siemens SINUMERIK 810D - Page 330

Starting Up HMI Embedded (IM2) 08/2005
4 Functions/Parameterization
© Siemens AG, 2005. All rights reserved
IM2/4-80 SINUMERIK 840D sl/840D/840Di/810D HMI Installation and Start-Up Guide (IAM) – 08/2005 Edition
9218 USER_CLASS_SELECT_PROGRAM
H04, H05
CR: A2
- Protection level 'Program selection' BYTE 3/4
OP30, Adv, Emb OP30: 7, Adv: 7,
Emb: 7
0 7
IMMEDIATE
LY
-
9219 USER_CLASS_TEACH_IN
H04, H05
CR: A2
- Protection level TEACH IN BYTE 3/4
OP30, Adv, Emb OP30: 7, Adv: 7,
Emb: 7
0 7
IMMEDIATE
LY
-
9220 USER_CLASS_PRESET
H04, H05
CR: A2
- Protection level PRESET BYTE 3/4
OP30, Adv, Emb OP30: 7, Adv: 7,
Emb: 7
0 7
IMMEDIATE
LY
-
9221 USER_CLASS_CLEAR_RPA
H04, H05
CR: A2
- Protection level delete R parameters BYTE 3/4
OP30, Adv, Emb OP30: 7, Adv: 7,
Emb: 7
0 7
IMMEDIATE
LY
-
9222 USER_CLASS_WRITE_RPA
H04, H05
CR: A2
- Protection level write R parameters BYTE 3/4
OP30, Adv, Emb OP30: 7, Adv: 7,
Emb: 7
0 7
IMMEDIATE
LY
-
9223 USER_CLASS_SET_V24
H04, H05
CR: A2
- Protection level RS-232 interface parameterization BYTE 3/4
OP30, Emb OP30: 7, Emb: 7
0 7
IMMEDIATE
LY
-
9224 USER_CLASS_READ_IN
H04, H05
CR: A2
- Protection level read in data BYTE 3/4
OP30, Emb OP30: 7, Emb: 7
0 7
IMMEDIATE
LY
-
9225 USER_CLASS_READ_CST
H04, H05
CR: A2
- Protection level standard cycles BYTE 3/4
OP30, Emb OP30: 7, Emb: 7
0 7
IMMEDIATE
LY
SW 2
9226 USER_CLASS_READ_CUS
H04, H05
CR: A2
- Protection level user cycles BYTE 3/4
OP30, Emb OP30: 7, Emb: 7
0 7
IMMEDIATE
LY
SW 2
9227 USER_CLASS_SHOW_SBL2
H04, H05
CR: A2
- Skip single block2 (SBL2) BYTE 3/4
Emb Emb: 7
0 7
IMMEDIATE
LY
SW3.5
9228 USER_CLASS_READ_SYF
H04, H05
CR: A2
- Access level for selecting the directory SYF BYTE 3/4
Emb Emb: 7
0 7
IMMEDIATE
LY
SW4.2
9229 USER_CLASS_READ_DEF
H04, H05
CR: A2
- Access level for selecting the directory DEF BYTE 3/4
Emb Emb: 7
0 7
IMMEDIATE
LY
SW4.2
9230 USER_CLASS_READ_BD
H04, H05
CR: A2
- Access level for selecting the directory BD BYTE 3/4
Emb Emb: 3
0 7
IMMEDIATE
LY
SW4.2