Home
Soyer
Welding System
PH-9 SRM12
Soyer PH-9 SRM12 - User Manual
82 pages
Manual
Specs
Ask a question
Save Page as PDF
To Next Page
To Next Page
Loading...
EN
Operating
Instructions
Stud welding device
SRM® technology
BMK-8i ACCU
Stud welding gun
PH-9 SRM
12
PH-9 SRM
12
+G
PH-3N SRM
2
Table of Contents
Main Page
Default Chapter
3
Table of Contents
3
General Information
6
Validity of the Operating Instructions
6
Registered Trademarks
6
Abbreviations and Definitions
7
Declarations of Conformity
7
Manufacturer
9
Instruction, Training
9
Standards and Directives
9
Important Safety Instructions
10
Warning Signs Used
10
General Safety Instructions
11
Safety Instructions Regarding the Working Method
14
Electromagnetic Fields - Implants
15
Personal Protective Equipment
16
Intended Use of the Stud Welding Device
17
Incorrect Use
17
Intended Use of the Stud Welding Guns
17
Incorrect Use
18
Operating Company Prerequisites
18
Prerequisites for Personnel
18
Important Safety Instructions for Battery Operation
20
Transport
23
Storage, Shutdown
23
Disposal
23
Description of the BMK-8I ACCU Stud Welding Device
24
Type Designation
24
Working Method
24
Stud Welding with SRM® Technology
25
Drawn Arc Stud Welding Technology Using Shielding Gas
26
Overview of the Controls
27
Display and Setting Range
29
Battery Charging and Status Indicators
30
Technical Data of the BMK-8I ACCU Stud Welding Device
31
Maximum Settings
33
Permitted Stud Welding Guns
34
Cleaning the Stud Welding Device
35
Description of the SRM® Stud Chuck
36
Adjusting SRM® Stud Chucks
36
Description of the PH-9 SRM Stud Welding Gun
38
Technical Data of the PH-9 SRM
39
Stud Welding Gun
39
Installing the SRM® Stud Chuck in PH-9 SRM 12
40
Replacing the SRM 12 Support Tube Insert of PH-9 SRM
42
Cleaning of the Stud Welding Gun
43
Description of the PH-9 SRM +G Stud Welding Gun
44
Technical Data of the PH-9 SRM
45
12 +G Stud Welding Gun
45
Operation of the PH-9 SRM
46
12 +G
46
Safety Check
46
Welding with the PH-9 SRM
47
Installing the SRM® Stud Chuck in PH-9 SRM
47
12 +G
47
Replacing the SRM Support Tube Insert of PH-9 SRM
50
Support Tube Insert of PH-9 SRM 12 +G
50
Cleaning of the Stud Welding Gun
52
Description of the PH-3N SRM Stud Welding Gun
53
Technical Data of the PH-3N SRM Stud Welding Gun
54
Installing the SRM® Stud Chuck in PH-3N SRM
55
Cleaning of the Stud Welding Gun
57
Setup and Connection
58
Requirements for the Installation Location
58
Connection of the Stud Welding Device and the Stud Welding Guns
59
Mains Connection
59
Connecting the Earth Cable
59
Connecting the Stud Welding Gun
60
Connecting the Shielding Gas Supply
60
Settings
64
Adjusting the Welding Parameters
64
Support Tables for Device Settings
65
Adjusting Welding Current and Welding Time
66
Adjusting/Deactivating SRM® Current
67
Adjusting the Gas Pre-Flow Time
68
Adjusting the Lift Time (Height of Lift) in the Setting Mode
69
Welding Operation
72
Carrying out Welding
72
Notes on Checking the Quality of the Weld
74
Visual Inspection
74
Switching off the Device
75
Welding Defects and Their Causes
76
Maintenance and Repair
80
Service
80
Warranty Conditions
80
Other manuals for Soyer PH-9 SRM12
Operating Manual
74 pages
Need help?
Do you have a question about the Soyer PH-9 SRM12 and is the answer not in the manual?
Ask a question
Soyer PH-9 SRM12 Specifications
General
Input Voltage
230V
Frequency
50/60 Hz
No-load Voltage
65V
Protection Class
IP21S
Welding process
MMA
Dimensions
210 mm
Related product manuals
Soyer BMS-8N
58 pages
Soyer BMS-8NV
58 pages
Soyer BMK-12 W
81 pages
Soyer BMK-12W
34 pages
Soyer BMH-22i
74 pages
Soyer BMS-9 ACCU
52 pages
Soyer BMK-8i
82 pages
Soyer BMK-8i ACCU
82 pages
Soyer BMK-10i
74 pages
Soyer BMK-8 U
68 pages
Need help?
General
To Next Page
