Appendix D: Events and Messages
- 145 -
Trouble condition Description
CPM 2 SG-TCP4 Fail Displayed when the TCP automation connection 4 is not connected/not responding to heartbeats
CPM 1 SG-TCP Logging Fail Displayed when the TCP automation logging connection is not connected/not responding to heartbeats
CPM 2 SG-TCP Logging Fail Displayed when the TCP automation logging connection is not connected/not responding to heartbeats
CPM 1 TCP Printer 1 Fail Displayed when the TCP printer is off-line - Primary SG-CPM5
CPM 2 TCP Printer 1 Fail Displayed when the TCP printer is off-line - Secondary SG-CPM5
CPM 1 SG-TCP Fail Displayed when the TCP automation is not connected/not responding to heartbeats - Primary SG-CPM5
CPM 2 SG-TCP Fail
Displayed when the TCP automation is not connected/not responding to heartbeats - Secondary SG-
CPM5
CPM 1 UPS Battery Fail
Displayed when the input of the receiver for UPS Battery is activated. This input is triggered by the UPS
to indicate an internal battery trouble - Primary SG-CPM5
CPM 2 UPS Battery Fail
Displayed when the input of the receiver for UPS Battery is activated. This input is triggered by the UPS
to indicate an internal battery trouble - Secondary SG-CPM5
CPM 1 UPS AC Fail
Displayed when the input of the receiver for UPS AC is activated. This input is triggered by the UPS to
indicate a loss of AC power - Primary SG-CPM5
CPM 2 UPS AC Fail
Displayed when the input of the receiver for UPS AC is activated. This input is triggered by the UPS to
indicate a loss of AC power - Secondary SG-CPM5
PSU 1 Fail
SG-PSU5 1 - provides power to all modules of the system. This trouble will be displayed if the power
supply fails or is removed from the system or the total current draw exceeds rating for the power supply
installed in the primary slot.
PSU 2 Fail
SG-PSU5 2 - provides power to all modules of the system. This trouble will be displayed if the power
supply fails or is removed from the system or the total current draw exceeds rating for the power supply
installed in the secondary slot.
Fan Tray 1 Trouble This trouble condition occurs when fan Tray 1 fails or slows down to an undesirable speed
Fan Tray 2 Trouble This trouble condition occurs when fan Tray 2 fails or slows down to an undesirable speed
Fan Tray 3 Trouble This trouble condition occurs when fan Tray 3 fails or slows down to an undesirable speed
Fan Tray 4 Trouble This trouble condition occurs when fan Tray 4 fails or slows down to an undesirable speed
CPM 1 Fan Trouble
This trouble condition occurs when the Primary SG-CPM5 fan tray fails or slows down to an undesir-
able speed
CPM 2 Fan Trouble
This trouble condition occurs when the Secondary SG-CPM5 fan tray fails or slows down to an undesir-
able speed
CPM 1 Temperature Warning
This trouble occurs when the internal board temperature of the Primary SG-CPM5 reached 65 degrees
Celsius
CPM 2 Temperature Warning
This trouble occurs when the internal board temperature of the Secondary SG-CPM5 reached 65 degrees
Celsius
PSU Compatibility Fail The two power supplies installed are not at the same power rating
CPM 1 RTC Battery Fail
The backup battery for the RTC chip has reached a low voltage condition - The battery check is per-
formed every day at midnight (00:00:00)
CPM 2 RTC Battery Fail
The backup battery for the RTC chip has reached a low voltage condition - The battery check performed
every day at midnight (00:00:00)
CPM1 Absent Message is displayed if the secondary SG-CPM5 cannot communicate with the primary SG-CPM5
CPM2 Absent Message is displayed if the primary SG-CPM5 cannot communicate with the secondary SG-CPM5
CPM 1 Auxiliary CPU Fail This message is displayed when the Auxiliary CPU fails on the primary SG-CPM5
CPM 2 Auxiliary CPU Fail This message is displayed when the Auxiliary CPU fails on the secondary SG-CPM5
UIB 1 Cable Fail
This message is displayed when the primary User Interface Board communication is lost
Possible Causes - Hardware ID cannot be read, Power disconnected to the display, display cable dis-
connected
UIB 2 Cable Fail
This message is displayed when the secondary User Interface Board communication is lost
Possible Causes - Hardware ID cannot be read, Power disconnected to the display, display cable dis-
connected
CPM 1 EMMC Fail
This trouble condition is displayed when the EMMC memory fails (cannot be read from or written to) –
Future Release
CPM 2 EMMC Fail
This trouble condition is displayed when the EMMC memory fails (cannot be read from or written to) –
Future Release
To Next Page
Loading...
