1.0 Table of Contents
- 3 -
4.3.3 SG-DRL-IP setup 33
4.3.3.1 Line card fan tray installation 33
4.3.3.2 Paddle card installation 34
4.3.3.3 EMMC memory 34
4.3.3.4 DDR3 memory 35
4.3.3.5 SD card 35
4.4 SG-DRL5-IP PAD – SG-DRL5-IP paddle card 36
4.5 SG-S5LFANTR - Line card fan tray 36
4.6 SG-DRL5/DRL5E/DRL5-2L - Line card 37
4.7 SG-DRL5-PAD - Paddle card 37
4.8 SG-DRL5-ADPT - Adapter card 38
4.9 SG-DRL4-2L upgrade to System 5 39
Converting SG-DRL4-2L line cards to SG-DRL5-2L line cards 39
4.10 Installing SG-DRL5 PSTN cards in a SG-System 5 40
4.11 SG-PSU5 250W and 600W power supply 41
4.11.1 SG-PSU5-600/SG-PSU5-250 installation 42
4.11.2 Power management 42
4.12 SG-UIB5 - User interface 42
4.12.1 SG-UIB5 LCD replacement 43
4.13 SG-SYS5MEM4 - Expandable EMMC 44
4.14 DDR3 RAM 45
4.15 SD card 45
5.0 Operation 46
5.1 Basic operation 47
5.1.1 Connectivity 47
5.1.2 SG-System 5 Console software 47
5.1.2.1 Visual verification 47
5.1.2.1.1 Connectivity 47
5.1.2.1.2 Functionality 47
5.1.2.1.3 Header file 47
5.1.2.1.4 Unique ID 47
5.1.2.1.5 Automation and printer messages 47
5.1.2.1.6 ACK 47
5.1.2.1.7 NACK from the console or automation software 47
5.1.2.1.8 NACK from the receiver 48
5.1.2.1.9 No response from the console software 48
5.1.2.1.10 No response from the receiver 48
SG-DRL5-IP – Visual verification 48
SG-CPM5 - SG visual commands 48
5.1.2.2 Advanced output protocol specification 48
5.2 Printer 48
5.2.1 Introduction 48
5.2.2 TCP/IP 48
5.2.3 Serial 49
5.3 AHS table management 49
5.4 Automation 50
5.4.1 Automation input/output 50
5.4.2 Automation compatibility 50
5.4.3 Automation protocols 50
5.4.4 Acknowledgment of the signal 50
5.4.5 COM responses 50
5.4.6 Automation absent 50
5.4.7 SIA internal status output 51
5.4.8 Line card addressing 51
5.5 Operation - LCD user interface 51
5.5.1 Bootup 51
5.5.2 Calibration 52
5.5.3 Home screen 53
5.5.3.1 Status banner 53
5.5.3.2 Type - unit IP 53
5.5.3.3 Active mode 53
5.5.3.3.1 SG-TCP 53
5.5.3.3.2 SG- SERIAL 53
5.5.3.3.3 SG-ALL 54
To Next Page
Loading...
