Technogym Run XT - Page 6

RUN XT: Service & Maintenance Manual - rev. 2.0
Page ii
7.2. DISASSEMBLING THE EPROM .........................................................................................................................7.2
7.3. DISASSEMBLING THE CPU BOARD...................................................................................................................7.3
7.4. DISASSEMBLING THE KEYBOARD ...................................................................................................................7.4
7.5. DISASSEMBLING THE CARDIO RECEIVER.........................................................................................................7.5
7.6. DISASSEMBLING THE EMERGENCY BUTTON ....................................................................................................7.8
7.7. DISASSEMBLING THE MOTOR GUARD............................................................................................................7.10
7.8. DISASSEMBLING THE FRONT PLATE..............................................................................................................7.11
7.9. DISASSEMBLING THE RUNNING TRACK.........................................................................................................7.12
7.10.DISASSEMBLING THE DRIVEN ROLLER, THE DRIVING ROLLER, THE TREAD BELT AND THE MOTOR BELT............7.14
7.11.DISASSEMBLING THE BELT MOTOR...............................................................................................................7.17
7.12.DISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS .....................................................................................7.19
7.13.DISASSEMBLING THE INVERTER...................................................................................................................7.20
7.14.DISASSEMBLING THE UP-DOWN MOTOR BELT ...............................................................................................7.21
7.15.DISASSEMBLING THE UP-DOWN MOTOR........................................................................................................7.22
7.16.DISASSEMBLING THE UP-DOWN MOTOR BRUSHES..........................................................................................7.25
7.17.DISASSEMBLING THE ELEVATION BARS ........................................................................................................7.26
7.18.DISASSEMBLING THE LEAD SCREW NUTS ......................................................................................................7.27
7.19.DISASSEMBLING THE LIMIT SWITCHES..........................................................................................................7.29
7.20.DISASSEMBLING THE PHOTOCELL ................................................................................................................7.30
8. ADJUSTMENTS ...............................................................................................................................................8.1
8.1. TENSIONING A NEW TREAD BELT ..................................................................................................................8.1
8.2. TENSIONING A USED TREAD BELT ..................................................................................................................8.2
8.3. CENTERING THE TREAD BELT ........................................................................................................................8.3
8.4. ADJUSTING THE TENSION AND ALIGNMENT OF THE TREAD-BELT MOTOR BELT .................................................8.4
8.5. TENSIONING THE UP-DOWN MOTOR BELT.......................................................................................................8.6
8.6. ALIGNING THE ELEVATION BARS ...................................................................................................................8.7
8.7. CALIBRATING THE TREAD BELT SPEED ...........................................................................................................8.8
8.8. CENTERING THE PHOTOCELL.........................................................................................................................8.9
9. MACHINE CONFIGURATION.......................................................................................................................9.1
9.1. CHANGING THE SETTINGS ON THE DISPLAY PANEL..........................................................................................9.1
9.1.1. Language used .................................................................................................................................9.1
9.1.2. Measurement system.........................................................................................................................9.1
9.1.3. Maximum time..................................................................................................................................9.2
9.1.4. Activating the “+” and “−” keys......................................................................................................9.2
9.1.5. Disabling the function keys...............................................................................................................9.2
9.1.6. Enabling the “ENTER” key..............................................................................................................9.2
9.2. MAINTENANCE INFORMATION .......................................................................................................................9.3
9.2.1. Hours on ..........................................................................................................................................9.3
9.2.2. Hours of use .....................................................................................................................................9.3
9.2.3. Hours of motor use ...........................................................................................................................9.3
9.2.4. Minutes of up-down motor use..........................................................................................................9.3
9.2.5. Distance travelled ............................................................................................................................9.3
9.3. CHANGING THE MAINTENANCE INFORMATION................................................................................................9.3
9.3.1. Hours on ..........................................................................................................................................9.3
9.3.2. Hours of use .....................................................................................................................................9.4
9.3.3. Hours of motor use ...........................................................................................................................9.4
9.3.4. Minutes of up-down motor use..........................................................................................................9.4
9.3.5. Distance travelled ............................................................................................................................9.4
9.4. PROGRAMMING THE HITACHI J100 INVERTER .............................................................................................9.5
9.4.1. Version E2........................................................................................................................................9.5
9.4.2. Versions E3, E4 and E5....................................................................................................................9.5
10.SCHEDULED MAINTENANCE....................................................................................................................10.1
11.APPENDIX......................................................................................................................................................11.1