Technogym Selection M810 - Page 7

SELECTION LINE: Service & Maintenance Manual - rev. 4.0
Page iii
5.7. THE TUBE STARTS TO WABBLE ......................................................................................................................... 5.9
5.8. THE BACKREST OF THE ADJUSTABLE BENCH (P820/P920) FALLS DOWN – DISENGAGES DURING USE ................. 5.10
5.8.1. check the selector pin ........................................................................................................................ 5.10
5.8.2. tighten the safety grub screw ............................................................................................................. 5.14
5.9. THE ADDITIONAL WEIGHT SUPPORT HAS BREAKAGE PROBLEMS ........................................................................ 5.19
5.9.1. Equipment provided with plastic support and 0G000232-KG/LB “spring” selector........................ 5.20
5.9.2. Equipment provided with metallic springs and H0000511-KG/LB selector. .................................... 5.21
5.10. THE GAS SPRING OF THE SHOULDER REST DEVICE IS DAMAGING ....................................................................... 5.22
5.11. THERE ARE PROBLEMS FOR THE JOINT ON ARM EXTENSION MACHINE ............................................................. 5.23
5.11.1. Machines with old M18 joint ............................................................................................................. 5.23
5.11.2. Machines with M12 joint ................................................................................................................... 5.24
5.12. THERE IS PLAY ON ROTARY TORSO LEVER ....................................................................................................... 5.25
5.12.1. Already-installed machines ............................................................................................................... 5.25
5.12.2. New machines .................................................................................................................................... 5.26
5.13. LEVERS BECOMING MISALIGNED ON EASY CHIN DIP ........................................................................................ 5.27
5.14. IT’S DIFFICULT TO SELECT THE EXERCISE START POSITION ON ABDUCTOR AND ADDUCTOR ............................. 5.28
5.14.1. Flanges .............................................................................................................................................. 5.28
5.14.2. selector lever ..................................................................................................................................... 5.28
5.14.3. Washers ............................................................................................................................................. 5.29
5.15. SEAT ON P820 P920 ADJUSTABLE BENCH IS DAMAGING ................................................................................... 5.30
5.16. THE ROD FOR ADJUSTING THE BACKREST ON THE CRUNCH BENCH AND THE LOWER BACK BENCH IS
DAMAGING ........................................................................................................................................................ 5.31
5.17. IT’S DIFFICULT TO ROTATE THE BARBELL ON THE MULTIPOWER ....................................................................... 5.32
5.18. BEARINGS ON CHEST PRESS / CHEST INCLINE LEVERS ARE DAMAGING ............................................................ 5.33
5.19. CABLE SLIP OFF ON LEG PRESS PULLEY ............................................................................................................ 5.33
5.20. CABLE SLIP OFF ON PECTORAL MACHINE .......................................................................................................... 5.34
5.21. THE HOOK OF MULTIPOWER BECOMES FREE ...................................................................................... 5.34
5.22. WHAT TO DO IF THE CABLE SLIPS OFF THE CAMS / PULLEYS OF THE MACHINE .................................................... 5.34
6. COMPONENTS DISASSEMBLY .......................................................................................................................... 6.1
6.1. SEAT ON LOW MACHINES .................................................................................................................................... 6.1
6.2. SEAT ON TALL MACHINES ................................................................................................................................... 6.2
6.3. LEG PRESS SEAT ................................................................................................................................................. 6.4
6.4. EASY START FOR TALL MACHINES ....................................................................................................................... 6.6
6.5. RELEASE LEVER .................................................................................................................................................. 6.8
6.6. SELECTOR SWITCH FOR ADDITIONAL WEIGHT .................................................................................................... 6.10
6.6.1. Machines with cross with crimped cable fitting ................................................................................ 6.10
6.6.2. Machines with cross with doubling pulley ......................................................................................... 6.11
6.7. COUNTERWEIGHT CABLE ON MULTI POWER ..................................................................................................... 6.13
6.8. BARBELL GUIDE SLEEVES ON THE MULTI POWER ............................................................................................. 6.15
6.9. FRONT WEIGHT STACK CASING.......................................................................................................................... 6.16
6.10. TOP 6.17
7. SPECIAL OPERATIONS ....................................................................................................................................... 7.1
7.1. LOCKING DOWN THE CABLE FIXING DOWELS ....................................................................................................... 7.1
7.2. LOCKING DOWN THE PULLEYS ............................................................................................................................ 7.2
7.3. LOCKING DOWN THE DOWELS ON THE ARM EXTENSION LEVER .......................................................................... 7.2
7.4. FIX THE HOOK ON THE BAR OF MULTIPOWER: SOLUTION TO PREVENT THE HOOK FROM
BECOMING FREE ........................................................................................................................................... 7.3
7.4.1. EQUIPMENTS WITH SN UP TO M95315100401 .............................................................................. 7.3
7.4.2. equipment with sn starting from m95315100402 ................................................................................ 7.5
7.5. TIGHTEN THE SAFETY GRUB SCREW IN THE ADJUSTABLE BENCH (P820/P920) ..................................................... 7.7
8. WEIGHT STACK CABLE ..................................................................................................................................... 8.8
8.1. LENGTH OF THE WEIGHT STACK CABLE ............................................................................................................... 8.8
8.2. ROUTING OF THE WEIGHT STACK CABLE ............................................................................................................. 8.9
8.2.1. M810 – Leg Curl ................................................................................................................................. 8.9