8
© 2012 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO556/656/756/856(Ver03)
ERROR CODE AND TROUBLESHOOTING
8 - 15
CF00 Finisher related
service call
Belt escape unit home position error detection: The belt
escape unit does not leave the home position when the
Knurled belt motor has been driven for specified time.
[MJ-1029]
P. 8 - 119
CF10 Undefined error code processing: If the engine of the
equipment judges that a code (command) other than the
defined error codes is sent from the finisher, it regards
this as a CF10 error.
P. 8 - 119
CF70 New toner transport motor abnormality: The new toner
transport motor does not run normally when new toner is
supplied.
P. 8 - 1 22
CF80 Hopper motor lockup: The hopper motor does not run
normally when the power is ON or the copying is started.
P. 8 - 1 22
F070 Communication
related service call
Communication error between System-CPU and Engine-
CPU
P. 8-95
F090 Circuit related
service call
SRAM abnormality on SYS board P. 8-122
F100_0 Other service call HDD format error: Operation of HDD key data fails. P. 8-123
F100_1 HDD format error: Encryption key data of either the SYS
board or the SRAM board are damaged.
P. 8 - 1 23
F100_2 HDD format error: Encryption key data of both the SYS
board and the SRAM board are damaged.
P. 8 - 1 24
F101_0 HDD connection error (HDD connection cannot be
detected.)
P. 8 - 1 25
F101_1 Root partition mount error (HDD formatting fails.): The
HDD cannot be connected (mounted) caused by damage
to the areas in which the program is mainly stored.
P. 8 - 1 25
F101_2 Normal partition mount error (HDD normal partition
mounting fails.): The HDD cannot be connected
(mounted) caused by damage to areas other than those
described in the F101_0 and F101_1 errors.
P. 8 - 1 26
F101_3
Encryption partition mount error (HDD encryption
partition mounting fails.): The HDD cannot be
connected (mounted) caused by damage to the
areas in which the key is stored.
P. 8 - 1 26
F101 The HDD cannot be connected (mounted) caused by a
reason other than one described in the F101_0 through
F101_3 errors.
P. 8 - 1 26
F102 HDD boot error: HDD does not become ready for booting. P. 8-126
F103 HDD data transfer time-out: Data reading or writing is not
executed in a specified period of time.
P. 8 - 1 26
F104 HDD data error: Abnormality is detected in the data of the
HDD.
P. 8 - 1 26
F105 Other HDD errors P. 8-126
F106_0 ADI-HDD error: Illegal disk replacement detected (ADI-
HDD Exchange to SATA-HDD).
P. 8 - 1 27
F106_1 .ADI-HDD error: HDD type detection error P. 8-127
F106_2 .ADI-HDD error: ADI encryption key download operation
error
P. 8 - 1 28
F106_3 .ADI-HDD error: ADI authentication Admin Password
generation error
P. 8 - 1 28
F106_4 .ADI-HDD error: Authentication random number
generation error
P. 8 - 1 29
F106_5 .ADI-HDD error: Authentication data transmission error P. 8-129
F109_0 Key consistency error: Consistency check operation
error.
P. 8 - 1 29
F109_1 Key consistency error: SRAM encryption AES key data
damage.
P. 8 - 1 30
F109_2 Key consistency error: Signature Check public key
damage.
P. 8 - 1 30
Error code Classification Contents Troubleshooting
To Next Page
Loading...
