Toshiba GX9 - Page 265

GX9 ASD Installation and Operation Manual 253
Regenerative Braking Stall Prevention Mode Selection,
157
Regenerative Braking Torque Limit 1, 155
Regenerative Braking Torque Limit 1 Level, 155
Regenerative Braking Torque Limit 2 Level, 156
Regenerative Braking Torque Limit 3 Level, 156
Regenerative Braking Torque Limit 4 Level, 156
Regenerative Power Ridethrough Control Level, 190
Regenerative Power Ridethrough Selection, 130
Remote EOI Hardware, 36
Remote Mode, 33
RES, 20, 21
RES terminal, 21
Reset, 78
Retry Selection, 131
Retry/Restart, 51
Reverse Speed Limit Input Level, 153
Reverse Speed Limit Input Selection, 153
Ridethrough Time, 134
Rocking Start, 199
ROM Fault, 229
Root menu mapping, 39
Root Menus, 39
Rotary Encoder, 33
RR, 20, 42
RR Input Bias, 158
RR Input Gain, 158
RR Input Point 1 Frequency, 110
RR Input Point 1 Torque, 112
RR Input Point 2 Frequency, 111
RR Input Point 2 Torque, 112
RR Reference Point 1, 110
RR Reference Point 2, 111
RR terminal, 22
RS232, 26
RS232/RS485 Wire Count, 203
RS485, 26
Run External Devices, 44
Run Frequency, 123
Run Frequency Hysteresis, 123
Run Key, 33
Run Time, 41
RX, 20, 42
RX Input Bias, 158
RX Input Gain, 159
RX Input Point 1 Frequency, 113
RX Input Point 1 Torque, 115
RX Input Point 2 Torque, 115
RX Point 2 Frequency, 114
RX Reference Point 1, 113
RX Reference Point 2, 114
RX terminal, 22
RX2, 42
RX2 Input Bias, 159
RX2 Input Gain, 159
RX2 Input Point 1 Frequency, 116
RX2 Input Point 1 Torque, 118
RX2 Input Point 2 Frequency, 117
RX2 Input Point 2 Torque, 119
RX2 Point 1 Frequency, 116
RX2 Reference Point 1, 116
RX2 Reference Point 2, 117
S
S/L2, 17
S1, 20
S1 terminal, 21
S2, 20
S2 terminal, 21
S3, 20
S3 terminal, 21
S4, 20
S4 terminal, 21
Scan Rate, 134
S-Curve Acceleration/Deceleration Pattern 1, 163
S-Curve Acceleration/Deceleration Pattern 2, 164
SEAL, 232
Sealing Water, 45
Sealing Water Error, 232
Search Inertia, 135
Search Method, 135
Selection for Over-Exciting Cooperation, 159
Selection of Number of PG Input Phases, 144
Send Waiting Time (RS232/RS485), 204
Send Waiting Time (TTL), 201
Settings, 44
Setup Wizard, 44, 71
Short Circuit Current Rating, 237
Short Circuit Detection At Start, 187
Short Circuit Pulse Duration, 187
Sink/Source Setting Error, 228
Sink/Source Switching, 26
Sleep Timer, 44
Slip Frequency Gain, 149
S-Pattern 1, 163
S-Pattern 2, 163
S-Pattern Acceleration Lower-Limit Adjustment, 166
S-Pattern Acceleration Upper-Limit Adjustment, 166
Special, 56
Special Parameters, 58
Speed at 0% Drooping Gain, 136
Speed at F320 Drooping Gain, 136
Speed Error, 228
Speed Limit (torque) Center Value Reference Selection,
154
Speed Limit (torque=0) Band, 154