Visonic PowerMaster-10 G2 Installer's Guide

D-303222 PowerMaster-10/30 G2 Installer's Guide 1
PowerMaster-10/30 G2
Version 16
Installer's Guide
Table of Contents
1. INTRODUCTION ................................................... 3
1.1 System Features ............................................ 3
2. CHOOSING THE INSTALLATION LOCATION ... 7
3. POWERMASTER-10 G2 INSTALLATION ........... 8
3.1 Opening the PowerMaster-10 G2 Control
Panel and Bracket Mounting .............................. 8
3.2 Connecting to the Telephone Line ............... 9
3.3 System Planning & Programming .............. 10
3.4 GSM Module Installation ............................. 10
3.5 PGM-5 Installation ....................................... 11
3.6 Adding Wired Zones or PGM Device ......... 12
3.7 Connecting Power to the Control Panel .... 13
3.8 Supplying Power to the Unit ....................... 16
3.9 Closing the PowerMaster-10 G2 Control
Panel ................................................................... 16
4. POWERMASTER-30 G2 INSTALLATION ......... 17
4.1 PowerMaster-30 G2 Wiring Diagram .......... 17
4.2 Opening the PowerMaster-30 G2 Control
Panel and Bracket Mounting ............................ 18
4.3 Connecting to the Telephone Line (detail
"M" in Figure 4.1) ............................................... 18
4.4 Connecting Wired Zone and Siren (detail
"B" in Figure 4.1)................................................ 19
4.5 System Planning & Programming .............. 19
4.6 GSM Module Installation (detail "N" in
Figure 4.1) ........................................................... 20
4.7 DUAL RS-232 Optional Module Mounting
(detail "F" in Figure 4.1) .................................... 20
4.8 PGM-5 Installation (located instead of detail
"F" in Figure 4.1) ................................................ 21
4.9 Optional Expander Module (detail "K" in
Figure 4.1) ........................................................... 22
4.10 Connecting Power to the Control Panel .. 24
4.11 Battery Insertion ........................................ 25
4.12 Supplying Power to the Unit ..................... 25
4.13 Closing the PowerMaster-30 G2 Control
Panel ................................................................... 26
5. PROGRAMMING ................................................ 27
5.1 General Guidance ....................................... 27
5.1.1 Navigation ........................................... 27
5.1.2 Feedback Sounds ............................... 27
5.2 Entering the "Installer Mode" and Selecting
a Menu Option ................................................... 27
5.2.1 Entering the "Installer Mode" if "User
Permit" is enabled ........................................ 28
5.2.2 Selecting options ................................ 28
5.2.3 Exiting the Installer Mode ................... 28
5.3 Setting Installer Codes ............................... 29
5.3.1 Identical Installer and Master Installer
Codes ........................................................... 29
5.4 Zones / Devices ........................................... 30
5.4.1 General Guidance & Zones/Devices
Menu Options............................................... 30
5.4.2 Adding New Wireless Devices or Wired
Sensors ........................................................ 30
5.4.3 Deleting a Device ................................ 34
5.4.4 Modifying or Reviewing a Device ....... 34
5.4.5 Replacing a Device ............................. 34
5.4.6 Defining Configuration Defaults for
"Device Settings" ......................................... 35
5.4.7 Updating Devices after Exiting Installer
Mode ............................................................ 36
5.5 Control Panel ............................................... 36
5.5.1 General Guidance – "Control Panel"
Flow-Chart & Menu Options ........................ 36
5.5.2 Configuring Arming/Disarming and
Exit/Entry Procedures .................................. 37
5.5.3 Configuring Zones Functionality ......... 38
5.5.4 Configuring Alarms & Troubles ........... 39
5.5.5 Configuring Sirens Functionality ......... 40
5.5.6 Configuring Audible & Visual User
Interface ....................................................... 41
5.5.7 Configuring Jamming and Supervision
(Missing device) ........................................... 42
5.5.8 Configuring Miscellaneous Features .. 43
5.6 Communication ........................................... 43

Visonic PowerMaster-10 G2 Specifications

General

Model	PowerMaster-10 G2
Category	Security System
Wireless Technology	PowerG
Remote Control	Yes
Event Log	1000 events
Communication	GSM, PSTN, IP
Frequency	868 MHz
Type	Wireless
Operating Temperature	-10°C to +55°C
Humidity	Up to 85% non-condensing