Why is the sun shading lowering too late in sunshine with my WAREMA Control Systems?
If the sun shading is lowered too late in the sunshine with your WAREMA Control Systems, the "Delay LOW" limit value may be set too high (sun control). Change the limit value.
How to fix a WAREMA Control System when sun shading system moves up too late in cloudy weather?
If the sun shading system moves up too late in cloudy weather, the HIGH limit value might be set too high in the sun control settings. Try changing the limit value.
What to do if the ice alarm is not triggered on my WAREMA Wisotronic?
If the ice alarm on your WAREMA Control Systems is not triggered, first ensure that ice monitoring is switched on. Next, check if the temperature limit value is set too low and change the limit value, noting the safety instructions. Also, verify that the sensor is properly connected, not faulty, and clean.
Why is a wind alarm triggered even in a gentle wind with WAREMA Wisotronic Control Systems?
If a wind alarm is triggered even in a gentle wind, it is likely that the wind speed limit is set too low. Increase the wind limit value, and observe the safety instructions.
Why does WAREMA Control System show "Fault" display in heading?
The "Fault" display in the heading indicates an issue. This could be due to a programmed bus device not being connected, in which case you should connect the device. It could also be due to reversed bus terminal polarity, so correct the connection.
Why is the ice alarm not triggered in my WAREMA Control System?
If the ice alarm is not triggered, first check if ice monitoring is switched off and, if so, switch it on. Also, the temperature limit value might be set too low. Change the limit value, noting the safety instructions. Finally, the sensor might not be connected, faulty, or dirty, so check and clean the sensor.
What to do if there is no display of weather data in WAREMA Wisotronic start menu?
If there is no display of weather data in the Wisotronic start menu, it may be because weather station 1 is not connected or parameterised. Note that only the measured values of weather station 1 are displayed. Connect the weather station and parameterise it as weather station 1.
What to do if my WAREMA Wisotronic sun shading system does not move with the sunlight level?
If your WAREMA Control Systems sun shading system does not move with the sunlight level, it might be because the sun control is switched off. Switch on the sun control.
What to do if control functions do not respond on my WAREMA Wisotronic Control Systems?
If the control functions of your WAREMA Control Systems do not respond, first check if the control functions are deactivated on the control panel. If so, activate control functions in the main menu and in the comfort functions. Another reason may be that a safety function is active.
Why does my WAREMA Wisotronic Control Systems respond sporadically to the EWFS Hand-held transmitter?
If the WAREMA Wisotronic responds only sporadically to an EWFS Hand-held transmitter, try reducing the distance to the Wisotronic to avoid interfering ambient influences. Also, check for interference from external transmitters such as baby monitors, and switch them off.
General safety information and warnings regarding the Wisotronic control system.
Explanation of warning symbols (DANGER, WARNING, CAUTION) and instructional pictograms.
Defines the proper use of the Wisotronic and safety precautions for window drives.
Identifies the intended audience for these instructions and emphasizes qualified personnel.
Key safety guidelines for operating automatically controlled sun shading systems.
Precautions for electrical installation and safe handling of mechanisms.
Guidelines and warnings concerning system modifications and component replacements.
Introduction to the initial setup and operation of the Wisotronic.
Description of the Wisotronic's start menu elements and navigation.
Navigating and understanding the Wisotronic's main menu options.
Step-by-step guide on how to set the date and time on the Wisotronic.
Instructions for adjusting display settings and changing operating element behaviour.
How to operate connected products directly via the Wisotronic control panel.
Introduction to basic and comfort functions for quick operation.
Core settings for new users to quickly configure the Wisotronic.
Activating or deactivating the automatic sun control feature.
Enabling or disabling the precipitation monitoring safety function.
Advanced settings for automatic sun shading control based on user preferences.
Configuration of automatic sun shading based on brightness levels.
Enabling/disabling the sun control feature for a channel.
Setting the brightness threshold for lowering sun shading products.
Assigning a delay time to prevent immediate reaction to brightness changes.
Defining the position for sun shading products when sunshine is detected.
Setting brightness for medium position and slat tilt in clear sky conditions.
Setting the brightness threshold for raising sun shading products.
Guidelines for setting SUN, CLEAR, and CLOUD limit values for optimal sun control.
Illustrates how brightness changes affect sun control operation with delay times.
Configuration for automatic sun shading based on lighting conditions at dawn/dusk.
Enabling or disabling the dawn/dusk control for a channel.
Setting brightness threshold for moving products at dawn.
Setting brightness threshold for moving products at dusk.
Illustrates dawn/dusk control operation based on brightness changes.
Automatic temperature-dependent control of sun shading products.
Overview of temperature control operating modes and requirements.
Activating or deactivating the temperature control per channel.
Setting the temperature limit for lowering products to provide shade.
Defining the product position for operation at higher temperatures.
Setting the temperature limit for raising products to allow sunlight.
Defining the product position for operation at lower temperatures.
Control based on difference between inside and outside temperatures.
Safety function to protect fabric products from precipitation.
Enabling or disabling the precipitation monitor.
Comfort function for preventing mould and ensuring fresh air via timed window control.
Programming specific times for raising or lowering sun shading products.
Function to prevent excessive cooling by locking automatic controls below a temperature.
Setting the outside temperature limit for raising products or closing windows.
Performing settings for manual operation of channels.
Defining the product position for manual DOWN operation.
Assigning WAREMA EWFS hand-held transmitters to Wisotronic channels.
Creating, storing, and retrieving scenes for automated actions.
Performing basic settings for the control unit and connected sensors.
Setting the current date and time on the Wisotronic.
Adjusting display view and behaviour of operating elements.
Setting the operating language of the Wisotronic interface.
Comparing and adjusting internal/external temperature sensor readings.
Overview of safety functions designed to protect sun shading products.
Safety function to protect products from wind damage by moving them to a safe position.
Safety function to prevent damage from frozen guide rails.
Setting whether the ice monitor automatically resets an ice alarm.
Procedure for manually resetting an ice alarm to avoid product damage.
Displaying a numbered list of faults in chronological order.
Guide to diagnosing and resolving common problems with the Wisotronic.
General| Brand | WAREMA |
|---|---|
| Model | Wisotronic |
| Category | Control Systems |
| Language | English |
To Next Page
