Yamaha MX360 - Electric Shock Prevention

CHECKING THE RECOIL STARTER
(MX360)............................................... 3-14
ASSEMBLING THE RECOIL 
STARTER (MX360) ............................. 3-15
FLYWHEEL............................................... 3-17
MZ360/MZ400 ..................................... 3-17
MX360 ................................................. 3-18
REMOVING THE FLYWHEEL ............. 3-19
INSTALLING THE FLYWHEEL............ 3-20
INSTALLING THE TCI UNIT ............... 3-20
GOVERNOR ............................................. 3-22
THROTTLE LEVER ASSEMBLY
(MX360BA6A0) ................................... 3-22
THROTTLE LEVER ASSEMBLY
(MX360C46A5/MX360AA6A0/
MX360AA6A5/MX360AA6A6) ............. 3-23
GOVERNOR ARM ASSEMBLY
(MX360KA6D0 for KOR) ..................... 3-24
GOVERNOR ARM ASSEMBLY 
(MZ360/MZ400/MX360KA6D0 
except for KOR) ................................... 3-25
FLYWEIGHT SHAFT ASSEMBLY 
(MZ360/MZ400)................................... 3-26
FLYWEIGHT SHAFT ASSEMBLY 
(MX360)............................................... 3-27
REMOVING THE FLYWEIGHT 
SHAFT ASSEMBLY AND 
GOVERNOR FORK............................. 3-28
DISASSEMBLING THE FLYWEIGHT
SHAFT ASSEMBLY............................. 3-28
CHECKING THE FLYWEIGHT 
SHAFT ASSEMBLY............................. 3-28
ASSEMBLING THE FLYWEIGHT 
SHAFT ASSEMBLY............................. 3-29
INSTALLING THE FLYWEIGHT 
SHAFT ASSEMBLY AND 
GOVERNOR FORK............................. 3-29
INSTALLING THE THROTTLE 
LEVER ASSEMBLY (Equipped 
models)................................................ 3-30
ADJUSTING THE GOVERNOR .......... 3-30
ENGINE SWITCH AND OIL WARNING 
UNIT.......................................................... 3-31
ENGINE SWITCH ............................... 3-32
CYLINDER HEAD COVER, CYLINDER
HEAD........................................................ 3-33
CHECKING THE ROCKER ARM........ 3-35
CHECKING THE PUSH ROD..............3-35
CHECKING THE CYLINDER HEAD ...3-35
INSTALLING THE CYLINDER HEAD
ASSEMBLY ..........................................3-36
VALVE .......................................................3-37
REMOVING THE VALVES AND 
VALVE SPRINGS.................................3-38
CHECKING THE VALVES AND 
VALVE SPRINGS.................................3-38
CHECKING THE VALVE SEATS .........3-40
VALVE LAPPING .................................3-42
INSTALLING THE VALVES AND 
VALVE SPRINGS.................................3-43
PISTON, CAMSHAFT, CRANKCASE, 
AND CRANKSHAFT.................................3-44
MZ360/MZ400 .....................................3-44
MX360 .................................................3-46
REMOVING THE BALANCER 
SHAFT, CAMSHAFT, AND VALVE 
LIFTER ................................................3-48
CHECKING THE BALANCER 
SHAFT .................................................3-48
CHECKING THE CAMSHAFT.............3-48
CHECKING THE VALVE LIFTER ........3-50
INSTALLING THE VALVE LIFTER,
BALANCER SHAFT, AND 
CAMSHAFT .........................................3-50
CHECKING THE CRANKCASE 
COVER ................................................3-50
INSTALLING THE CRANKCASE 
COVER ................................................3-51
CHECKING THE CYLINDER AND
PISTON................................................3-51
CHECKING THE CRANKCASE ..........3-53
CHECKING THE PISTON PIN ............3-53
CHECKING THE PISTON RINGS .......3-54
CHECKING THE CRANKSHAFT ........3-55
CHECKING THE CONNECTING 
ROD OIL CLEARANCE .......................3-56
INSTALLING THE PISTON AND 
PISTON RING......................................3-57
INSTALLING THE CRANKSHAFT.......3-57
SELECTING THE CRANKSHAFT 
SHIM....................................................3-59