Chapter 32 PPPoE IA
VES1724-56 User’s Guide
294
Tag Option Select the variables that you want the Switch to generate and add into the Agent Circuit ID
sub-option for PPPoE discovery packets with the specified VLAN tag. The variable options
include SP, SV, PV and SPV which indicate combinations of slot-port, slot-VLAN, port-VLAN
and slot-port-VLAN respectively in ASCII code. Alternatively, select private to have the
Switch use the Agent Circuit ID old format (slot-port-VLAN) in binary. An example of the port
number is 1 if you select private while it is 31 in ASCII code if you select SP, SV or SPV.
Delimiter
Select a delimiter to separate the Circuit ID information, slot ID, port number and/or VLAN
ID from each other. You can use a pound key (#), semi-colon (;), period (.), comma (,),
forward slash (/) or space. Select none to not use any delimiter.
Append Remote
ID
Select this option to have the Switch add the user-defined identifier string (specified in the
Remote ID Information field) to PADI or PADR packets from PPPoE clients.
Remote ID
Information
Select one of the following options:
Append Remote ID by user identifier: to have the Switch add the specified Remote ID
user identifier into the Agent Remote ID sub-option for PPPoE discovery packets with the
specified VLAN tag it forwards.
Append Remote ID by port name: to have the Switch use the name of the port on which
the PPPoE discovery packets with the specified VLAN tag are received and add it to the
PPPoE discovery packets.
Append Remote ID by user identifier + port name + port TEL: to have the Switch add
the specified Remote ID user identifier, the port’s name, and the port’s telephone number
into the Agent Remote ID sub-option for PPPoE discovery packets it forwards with the
specified VLAN tag.
Remote ID user
identifier
Enter a string of up to 63 ASCII characters that the Switch adds into the Agent Remote ID
sub-option for PPPoE discovery packets with the specified VLAN tag received on this port.
Spaces are allowed.
Remote ID
Delimiter
Select a delimiter to separate the Remote ID information, slot ID, port number and/or VLAN
ID from each other. You can use a pound key (#), semi-colon (;), period (.), comma (,),
forward slash (/) or space. Select none to not use any delimiter.
Add Click Add to insert a new VLAN-specific PPPoE IA entry to the Switch’s run-time memory.
The Switch loses these changes if it is turned off or loses power, so use the Save link on the
top navigation panel to save your changes to the non-volatile memory when you are done
configuring.
Cancel Click Cancel to reset the above fields to your previous configuration.
Clear Click Clear to set the above fields back to the factory defaults.
VID This field displays the ID number of the VLAN group to which the PPPoE IA settings apply.
Tag Option This field displays what information should be included in the Agent Circuit ID sub-option.
SP, SV, PV and SPV indicate combinations of slot-port, slot-VLAN, port-VLAN and slot-port-
VLAN respectively in ASCII code. Alternatively, select private to have the Switch use the
DHCP relay option 82 old format (slot-port-VLAN) in binary. The Switch uses a zero for the
slot value in the PADI and PADR packets. An example of the port number is 1 if you select
private while it is 31 in ASCII code if you select SP, SV or SPV.
Delimiter This field displays the delimiter used to separate the Circuit ID information, slot ID, port
number and/or VLAN ID from each other. none displays if no delimiter is used.
Circuit ID This field displays whether the Switch adds a string to the Agent Circuit ID sub-option
(Enable) or not (Disable).
Remote ID This field displays whether the Switch adds a string to the Agent Remote ID sub-option
(Enable) or not (Disable).
Delete Select the configuration entries you want to remove and click Delete to remove them.
Cancel Click Cancel to clear the Delete check boxes.
Table 136 Advanced Application > PPPoE IA Configuration > VLAN (continued)
LABEL DESCRIPTION
To Next Page
Loading...
