ABB ACSM1 - Page 367

Application program template
367
FIELDBUS
36
TLF9 500 µse c ( 1)
50.01 FBA ENABLE
(Drive value)
50.02 COMM LOSS FUNC
(Drive value)
50.03 COMM LOSS T OUT
(Drive value)
50.04 FBA REF1 MODESEL
(Drive value)
50.05 FBA REF2 MODESEL
(Drive value)
< 50.06 FBA ACT1 TR SRC
[ SPEED ACT ] (7 / 1.01)
< 50.07 FBA ACT2 TR SRC
[ TORQUE ] (1 / 1.06)
< 50.08 FBA SW B12 SRC
(Drive value)
< 50.09 FBA SW B13 SRC
(Drive value)
< 50.10 FBA SW B14 SRC
(Drive value)
< 50.11 FBA SW B15 SRC
(Drive value)
2.12 FBA MAIN CW
2.13 FBA MAIN SW
2.14 FBA MAIN REF1 2.15 FBA MAIN REF2
D2D COMMUNICATION
44
TLF9 500 µsec (2)
57.01 LINK MODE
(Drive value)
57.02 COMM LOSS FUNC
(Drive value)
57.03 NODE ADDRESS
(Drive value)
57.04 FOLLOWER MASK 1
(Drive value)
57.05 FOLLOWER MASK 2
(Drive value)
< 57.06 REF 1 SRC
[ SPEEDREF RAMPED ] (6 / 3.04)
< 57.07 REF 2 SRC
[ TO RQ REF TO TC ] (8 / 3.13)
< 57.08 FOLLOWER CW SRC
[ D2D FOLLOWER CW ] (4 / 2.18)
57.09 KERNEL SYNC MODE
(Drive value)
57.10 KERNEL SYNC OFFS
(Drive value)
57.11 REF 1 MSG TYPE
(Drive value)
57.12 REF1 MC GROUP
(Drive value)
57.13 NEXT REF1 MC GRP
(Drive value)
57.14 NR REF1 MC GRPS
(Drive value)
2.17 D2D MAIN CW
2.19 D2D REF1 2.20 D2D REF2
MECH BRAKE CTRL
30
TLF10 2 msec (2)
35.01 BRAKE CONTROL
(Drive value)
< 35.02 BRAKE ACKNOWL
(Drive value)
35.03 BRAKE OPEN DELAY
(Drive value)
35.04 BRAKE CLOSE DLY
(Drive value)
35.05 BRAKE CLOSE SPD
(Drive value)
35.06 BRAKE OPEN TORQ
(Drive value)
< 35.07 BRAKE CLOSE REQ
(Drive value)
< 35.08 BRAKE OPEN HOLD
(Drive value)
35.09 BRAKE FAULT FUNC
(Drive value)
3.14 BRAKE TORQ MEM
3.15 BRAKE COMMAND
DRIVE LOGIC
21
TLF10 2 msec (3)
10.01 EXT1 START FUNC
(Driv e value)
< 10.02 EXT1 START IN1
(Driv e value)
< 10.03 EXT1 START IN2
(Driv e value)
10.04 EXT2 START FUNC
(Driv e value)
< 10.05 EXT2 START IN1
(Driv e value)
< 10.06 EXT2 START IN2
(Driv e value)
< 10.07 JOG1 START
(Driv e value)
< 10.08 FAULT RESET SEL
(Driv e value)
< 10.09 RUN ENABLE
(Driv e value)
< 10.10 EM STOP OFF3
(Driv e value)
< 10.11 EM STOP OFF1
(Driv e value)
10.12 START INHIBIT
(Driv e value)
< 10.13 FB CW USED
[ FBA MAIN CW ] (4 / 2.12)
< 10.14 JOG2 START
(Driv e value)
< 10.15 JOG ENABLE
(Driv e value)
< 10.16 D2D CW USED
[ D2D M AIN CW ] (4 / 2.17)
< 10.17 START ENABLE
(Driv e value)
2.18 D2D FOLLOWER CW
6.01 STATUS WORD 1 6.02 STATUS WORD 2
6.03 SPEED CTRL STAT
6.05 LIMIT WORD 1
6.07 TORQ LIM STATUS
6.09 POS CTRL STATUS
6.10 POS CTRL STATUS2
6.11 POS CORR STATUS
START/STOP MODE
22
TLF10 2 msec (4)
11.01 START MODE
(Drive value)
11.02 DC MAGN TIME
(Drive value)
11.03 STOP MODE
(Drive value)
11.04 DC HOLD SPEED
(Drive value)
11.05 DC HOLD CUR REF
(Drive value)
11.06 DC HOLD
(Drive value)
11.07 AUTOPHASING MODE
(Drive value)
Page 4 Driv e L ogic FWA compatibility level = 1.46 Firmware Library ID = 1, ver = 1.0 Standard Library ID = 10000, ver = 1.1
Based on Customer Cust. Doc. No. Date
Prepar ed Approved Project name
Title Doc. des.
Resp. dept. Doc. No.