ABB SmartTouch B/stainless

Table of contents
Product manual 2CKA001473B5343
│
11
10.24.41 Basic stage heating - Control value difference for sending of heating control value ..................244
10.24.42 Basic stage cooling — Cyclic sending of the control value ........................................................244
10.24.43 Basic stage cooling — Hysteresis .............................................................................................245
10.24.44 Additional stage cooling — PWM cycle cooling (min) ................................................................245
10.24.45 Basic stage cooling — Maximum control value (0 - 255) ...........................................................245
10.24.46 Basic stage cooling — Minimum control value for basic load (0 to 255) ....................................245
10.24.47 Control of additional cooling stage ............................................................................................247
10.24.48 Control of additional cooling stage - Control value type .............................................................247
10.24.49 Control of additional cooling stage — Cooling type ...................................................................247
10.24.50 Control of additional cooling stage — P-component ..................................................................248
10.24.51 Control of additional cooling stage — I-component ...................................................................248
10.24.52 Control of additional cooling stage - Temperature difference to basic stage..............................248
10.24.53 Control of additional cooling stage — Extended settings ...........................................................249
10.24.54 Additional cooling stage ............................................................................................................250
10.24.55 Additional cooling stage — Mode of the control value ...............................................................250
10.24.56 Additional stage cooling — PWM cycle cooling (min) ................................................................250
10.24.57 Additional cooling stage — Control value difference for sending of cooling control value ..........250
10.24.58 Additional cooling stage — Cyclic sending of the control value .................................................251
10.24.59 Additional cooling stage — Maximum control value (0 - 255) ....................................................251
10.24.60 Additional cooling stage — Minimum control value for basic load (0 - 255) ...............................251
10.24.61 Additional cooling stage — Hysteresis ......................................................................................252
10.24.62 Settings of basic load ................................................................................................................253
10.24.63 Settings of basic load — Minimum control value for basic load > 0 ...........................................253
10.24.64 Basic load settings — Basic load active when controller is off ...................................................253
10.24.65 Combined heating and cooling modes ......................................................................................254
10.24.66 Combined heating and cooling modes — Switchover of heating/cooling ...................................254
10.24.67 Combined heating and cooling modes — Operating mode after reset ......................................254
10.24.68 Combined heating and cooling modes — Heating/cooling control value output ........................255
10.24.69 Combined heating and cooling modes — Additional heating/cooling stage control value
output ........................................................................................................................................255
10.24.70 Setpoint settings ........................................................................................................................256
10.24.71 Setpoint settings — Setpoint for heating comfort = setpoint for cooling comfort ........................256
10.24.72 Setpoint settings - Setpoint for standby and Eco are absolute values .......................................256
10.24.73 Setpoint settings - Hysteresis for switchover heating/cooling ....................................................256
10.24.74 Setpoint settings — Setpoint for heating and cooling comfort ...................................................257
10.24.75 Setpoint settings — Setpoint for heating comfort .......................................................................257
10.24.76 Setpoint settings — Setpoint for heating standby ......................................................................257
10.24.77 Setpoint settings — Reduction for standby heating by ..............................................................257
10.24.78 Setpoint settings — Setpoint for heating economy ....................................................................257
10.24.79 Setpoint settings — Reduction for heating economy by ............................................................258
10.24.80 Setpoint settings — Setpoint for heating building protection ......................................................258
10.24.81 Setpoint settings — Setpoint for cooling comfort .......................................................................258
10.24.82 Setpoint settings — Setpoint for cooling standby ......................................................................258
10.24.83 Setpoint settings — Increase for cooling standby by .................................................................259
10.24.84 Setpoint settings — Setpoint for cooling economy ....................................................................259
10.24.85 Setpoint settings — Increase for cooling economy ....................................................................259
10.24.86 Setpoint settings — Setpoint for cooling building protection ......................................................259
10.24.87 Setpoint settings — Setpoint setting via communication object (DPT 9.001).............................260
10.24.88 Setpoint settings — Display.......................................................................................................260
10.24.89 Setpoint settings - Hide temperature unit ..................................................................................260
10.24.90 Setpoint settings — Send current setpoint ................................................................................260
10.24.91 Setpoint settings - Cyclic sending of the current setpoint ..........................................................260