EasyManuals Logo

Ametek 241CE II User Manual

Ametek 241CE II
171 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #78 background imageLoading...
Page #78 background image
PN 903-8797, Rev A
The Stat\History menu items (listed in their viewing order) and their descrip-
tions are:
Sub-Menu Item Description
En\Dis Alrm? This prompt asks if you wish to enable\disable the out-of-specication (O-Spec) alarm.
To enable the O-Spec Alarm, press +. To disable the O-Spec Alarm, press ’.
Clear Alarm? This prompt asks if you wish to clear (reset) all current alarms (O-Spec or SCode).
To reset all current alarms, press +. The message “Cleared will be displayed. If you press ’,
Not Cleared will be displayed.
SCode z Basic Status Code and messages, where ‘z’ = the basic SCode (see below) along with its
corresponding message (if the alarm condition exists). If the alarm condition does not exist,
OK is displayed (e.g., SCode.# OK, where ‘#’ is the number corresponding with the SCode
message).
The basic SCodes and corresponding messages are listed below. The ‘w or ‘f preceding a
message indicates a ‘w’arning or ‘f’ault alarm condition.
Primary
Code
Error
Code # Message [Description]
1 1 w TimeOut [Stage-Time-Out]
2 2 w No H2O DP [Water-Dewpoint-Temperature-Not-Found] –
Available only if H2O DP:INT option is enabled from the
MonitorCFG menu.
4 3 w No HC DP [Hydrocarbon-Dewpoint-Temperature-Not-Found]
8 4 w Check XSCode [Advice – Review-Extended-Status-Code]
16 5 w Dirty Cell [Possible-Cell-Contamination]
32 6 f H2O Optics [Problem-In-Water-Side-Optical-Path]
64 7 f HC Optics [Problem-In-Hydrocarbon-Side-Optical-Path]
128 8 f Cool Cct [Problem-In-Cooling-Circuit]
XSCode z Extended Status Codes and messages, where ‘z’ = the XSCode (see below) along with its
corresponding message (if the alarm condition exists). If the alarm condition does not exist,
OK is displayed (e.g., XSCode.# OK, where ‘#’ is the number corresponding with the XSCode
message).
The XSCodes and corresponding messages are listed below. The ‘w or ‘f preceding a message
indicates a ‘w’arning or ‘f’ault alarm condition.
Primary
Code
Error
Code # Message [Description]
1 1 w EEP Warn [End-Of-EEPROM-Life]
2 2 w Hold TimeOut [Purging/Hold-Stage-Time-Out]
4 3 w Cool TimeOut [Cooling-Stage-Time-Out]
8 4 w Warm TimeOut [Warming-Stage-Time-Out]
16 5 w Cross Talk [Excessive-Mirror-Cross-Talk]
32 6 w High DP [Hydrocarbon-Dewpoint-Temperature-Too-High]
64 7 f High Temp [Mirror-RTD-Temperature-Is-Too-High]
128 8 f Low Temp [Mirror RTD-Temperature-Is-Too-Low]
256 9 f H2O Dim [Light-Intensity-On-Water-Side-Is-Too-Low]
512 10 f HC Dim [Light-Intensity-On-Hydrocarbon-Side-Is-Too-Low]
3-12 | 241CE II Hydrocarbon Dewpoint Analyzer

Table of Contents

Other manuals for Ametek 241CE II

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ametek 241CE II and is the answer not in the manual?

Ametek 241CE II Specifications

General IconGeneral
BrandAmetek
Model241CE II
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals