Anritsu LMR Master S412E

To Next Page

To Previous Page

7-10 :TRACe Subsystem Fixed WiMAX Commands

7-24 PN: 10580-00319 Rev. N S412E PM

EVM_SYM_STOP EVM vs. Symbol stop

Table 7-1. Available Parameters in WiMAX and Mobile WiMAX Mode (Sheet 3 of 3)

Parameter Name Description

Main Page

Default Chapter3
- Table of Contents3
Chapter 1-General Information11
- About this Manual11
- Introduction11
- Contacting Anritsu11
- Remote Programming Setup and Interface12
  - Remote Access Password12
  - Ethernet Interface Connection and Setup12
- Sending SCPI Commands17
Chapter 2-Programming With SCPI19
- Introduction19
- Introduction to SCPI Programming19
- SCPI Common Commands20
- SCPI Required Commands21
- SCPI Optional Commands21
- Subsystem Commands22
- Notational Conventions28
- Notational Examples29
  - Command Terminators29
- Formatting Conventions30
- Parameter Names30
Chapter 3-All Mode Commands31
- Introduction31
- Fetch GPS Subsystem31
- Instrument Subsystem32
- Mmemory Subsystem35
- Status Subsystem39
- System Subsystem40
- Sense]:Gps Subsystem41
Chapter 4-Spectrum Analyzer Commands43
- Abort Subsystem43
- Calculate Subsystem44
- Configure Subsystem63
- Display Subsystem65
- Fetch Subsystem67
- Format Subsystem69
- Initiate Subsystem70
- Measure Subsystem71
- Mmemory Subsystem74
- READ Subsystem77
- Trace Subsystem79
  - Trace Header Parameters80
- Trigger Subsystem91
- UNIT Subsystem93
- Sense] Subsystem94
Chapter 5-VNA Commands109
- Introduction109
- Calculate Subsystem109
- Display Subsystem142
- Format Subsystem148
  - Interpreting Returned Data Pair149
- Initiate Subsystem151
- Input Subsystem153
- Mmemory Subsystem155
- Source Subsystem158
  - Source:correction:rvelocity Subsystem158
- System Subsystem159
- Trace Subsystem160
- Sense] Subsystem172
Chapter 6-Vector Voltmeter Commands191
- Introduction191
- Fetch Subsystem191
- Mmemory Subsystem193
- Trace Subsystem196
- Sense] Subsystem198
Chapter 7-Fixed Wimax Commands201
- Abort Subsystem201
- Configure Subsystem202
- Display Subsystem205
- Fetch Subsystem207
- Format Subsystem210
- Measure Subsystem212
- Mmemory Subsystem216
- READ Subsystem219
- Trace Subsystem222
- Sense] Subsystem226
Chapter 9-LTE Commands261
- Abort Subsystem261
- Calculate Subsystem262
- Configure Subsystem265
- Display Subsystem268
- Fetch Subsystem269
- Format Subsystem272
- Initiate Subsystem273
- Measure Subsystem274
- READ Subsystem277
- UNIT Subsystem280
- Sense] Subsystem281
Chapter 10-P25 Phase 1 Commands288
- Configure Subsystem288
- Display Subsystem291
- Fetch Subsystem294
- Format Subsystem296
  - Interpreting Returned Data297
- Initiate Subsystem299
- Measure Subsystem300
- Mmemory Subsystem302
- READ Subsystem305
- Source Subsystem307
- Trace Subsystem310
- UNIT Subsystem320
- Sense] Subsystem321
Chapter 11-P25 Phase 2 Commands330
- Configure Subsystem330
- Display Subsystem333
- Fetch Subsystem337
- Format Subsystem339
  - Interpreting Returned Data340
- Initiate Subsystem342
- Measure Subsystem343
- Mmemory Subsystem345
- READ Subsystem349
- Source Subsystem351
- Trace Subsystem355
- UNIT Subsystem365
- Sense] Subsystem366
Chapter 12-NXDN Commands375
- Abort Subsystem375
- Configure Subsystem376
- Display Subsystem379
- Fetch Subsystem382
- Format Subsystem384
  - Interpreting Returned Data385
- Initiate Subsystem387
- Measure Subsystem388
- Mmemory Subsystem390
- READ Subsystem393
- Source Subsystem395
- Trace Subsystem398
- UNIT Subsystem407
- Sense] Subsystem408
Chapter 13-Dpmr Commands417
- Abort Subsystem417
- Configure Subsystem418
- Display Subsystem420
- Fetch Subsystem423
- Format Subsystem425
  - Interpreting Returned Data426
- Initiate Subsystem428
- Measure Subsystem429
- Mmemory Subsystem431
- READ Subsystem434
- Source Subsystem436
- UNIT Subsystem448
- Sense] Subsystem449
Chapter 14-DMR 2 Commands457
- Abort Subsystem457
- Configure Subsystem458
- Display Subsystem461
- Fetch Subsystem465
- Format Subsystem468
  - Interpreting Returned Data469
- Initiate Subsystem471
- Measure Subsystem472
- Mmemory Subsystem475
- READ Subsystem479
- Source Subsystem482
- UNIT Subsystem495
- Sense] Subsystem496
Chapter 15-PTC Commands505
- Abort Subsystem505
- Configure Subsystem506
- Display Subsystem508
- Fetch Subsystem511
- Format Subsystem513
  - Interpreting Returned Data514
- Initiate Subsystem516
- Measure Subsystem517
- Mmemory Subsystem520
- READ Subsystem524
- Source Subsystem527
- UNIT Subsystem541
- Sense] Subsystem542
Chapter 16-NBFM Commands551
- Abort Subsystem551
- Configure Subsystem552
- Display Subsystem555
- Fetch Subsystem559
- Format Subsystem563
  - Interpreting Returned Data564
- Initiate Subsystem566
- Measure Subsystem567
- Mmemory Subsystem571
- READ Subsystem574
- Source Subsystem578
- Trace Subsystem581
- UNIT Subsystem589
- Sense] Subsystem590
Chapter 17-TETRA Commands605
- Abort Subsystem605
- Configure Subsystem606
- Display Subsystem608
- Fetch Subsystem611
- Format Subsystem613
  - Interpreting Returned Data614
- Initiate Subsystem616
- Measure Subsystem617
- Mmemory Subsystem619
- READ Subsystem622
- Source Subsystem624
- Trace Subsystem627
- UNIT Subsystem635
- Sense] Subsystem636
Chapter 18-AM/FM/PM Commands643
- Calculate Subsystem643
- Display Subsystem647
- Format Subsystem648
- Initiate Subsystem650
- Mmemory Subsystem651
- Trace Subsystem654
- Sense] Subsystem655
Appendix A-Example663
- A-1 C/C++663
- Visual Basic665
Appendix B-Commands by Mode667

Anritsu LMR Master S412E - Page 224

Table of Contents

Related product manuals