EasyManua.ls Logo

Barco DP2K-12C - Page 80

Barco DP2K-12C
359 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
4. Troubleshooting
command (port = /dev/ttyS2:0) - set network ip-address to 10.140.162.141 (dhcp off) =Fromthe
touch panel, the IP address of the projector w as set to 10.140.162.141
command (port = 10.36.62.17:43680) - set network ip-address to 10.36.62.62 (dhcp off) =Froma
device w ith IP address 10.36.63.17, the IP address of the projector was c hanged to 10.36.63.17
command (port = /dev/ttyS0:0) - set dowser open. = From a touch panel or PC, c onnected serially (connector
labeled "Touc h panel"), the dowser was set t o open.
command (port = /dev/ttyS0:0) - set lamp off = From a touch panel or P C , connected serially (connector labeled
"Touch panel"), the lamp was pow ered off.
command (port = internal) - set lamp off = For an internal reason the state of the lamp was set to off.
command (port = button) - set dowser closed = The dowser was closed from the keypad.
The error m essages are explained in the troubleshooting list - code 58 31
ICP log les
Example of log le content :
2010/04/06 09:02:40.964797 I ICP application 1.2(126) init Shows the ICP package
2010/04/06 09:02:40.980964 I successfully initialized the LoginLevelProtection mutex
2010/04/06 09:02:41.039022 I Autotiming initialized
2010/04/06 09:02:41.049829 I Autotiming using VSyncs
2010/04/06 09:02:41.051245 I Started Autotiming Port threads
2010/04/06 09:02:41.051755 I Autotiming started
2010/04/06 09:02:41.052149 I Port thread running
2010/04/06 09:02:41.052897 I Port thread running
2010/04/06 09:02:43.632304 I Started Autotiming Main thread
2010/04/06 09:02:43.633017 D Autotiming thread running
2010/04/06 09:02:43.633476 D Autotiming: blank the image
2010/04/06 09:02:43.792939 D Autotiming: unblank the image
...
Form at
‘Date Time’ ‘Severity’ ‘message’
Where :
‘Date Time’ = the time w hen the event occurred.
‘Severity’ = On e character severity indication c an be : ’D” (Debug) E” (Error) I” ( Informational) - “U” (User).
‘message’ = T he actual error message.
Example :
24.03.2010 17:17:12.185 TPPL = 2848, APPL = 2048, TLPF = 4095, ALPF = 128
This line is entered when the auto timing on the ICP computes values that are not within valid range s.
Where :
TPPL = Total Pixels Per Line
APPL = Active Pixels Per Line
TLPF = Total Lines P er Frame
ALPF = Active Lines Per Frame
512 <= APPL <= TPPL <= 8191
288 <= ALP F <= TLPF <= 4095
In this exam ple ALPF = 128 which is less than the minimum of 288. When this happens, auto timing will attempt to blank the image.
76
R5905043 DP2K-12C/11CX 19/02/2018

Table of Contents

Other manuals for Barco DP2K-12C

Related product manuals