BioLogic BCS-810

To Next Page

To Previous Page

BCS-8xx series installation manual

Fig. 30: Network connection. One instrument to several PCs.

Alternatively, a single PC can control several instruments through the network.

Fig. 31: Network connection. One PC to several instruments.

Main Page

General Safety Considerations7
Table of Contents9
Introduction of the Product Range12
How to Read this Manual14
Modules Description14
BCS-COM Module14
BCS-COM Front Panel Detailed Description15
BCS-COM Rear Panel Detailed Description16
BCS-805 Module16
BCS-805 Front Panel Detailed Description16
BCS-805 Rear Panel Detailed Description17
BCS-810 Module18
BCS-810 Front Panel Detailed Description18
BCS-810 Rear Panel Detailed Description19
Auxiliary Inputs/Outputs (DB9) on Rear Panel of BCS-810 and BCS-80519
BCS-815 Module20
BCS-815 Front Panel Detailed Description21
BCS-815 Rear Panel Detailed Description22
BCS-PDU Module22
BCS-PDU Front Panel Detailed Description23
BCS-PDU Rear Panel Detailed Description24
Power Strip25
BCSC Cabinets and Module Mixing25
Modules and Cabinets Heights25
Software Features26
Getting Started27
Hardware Installation27
Preparing the Physical Installation of BCSC-38U and BCSC-24U Cabinets27
Safety Emergency Shutdown Installation27
Ventilation Requirements28
Electrical Plugs28
Unpacking and Inspection of BCSC-38U/BCSC-24U Cabinets30
Unpacking of BCSC-38U/BCSC-24U Cabinets Using the Lifting Rings30
Unpacking Procedure When Using a Forklift31
BCSC Cabinets Installation32
Electrical Equipment Requirements33
BCS-PDU Electrical Connections34
European Model34
North American Model35
Power Supply Connections35
Communication Connections37
Connection between BCS-COM and the BCS-8Xx Modules37
Connection between BCS-COM and the Computer37
Direct Ethernet Connection38
Network Connection38
Software Installation on the Computer40
BT-Lab Software Installation40
Errors During the Installation43
PC Installation and Configuration43
TCP/IP Installation and Configuration43
Connecting the PC with the Instrument46
Network Parameter Configuration with the Ethernet Connection46
Connection to the Computer with BT-Lab  Software46
Modification of the Instrument IP Address48
Windows Security Alert49
Connection to a Battery Cell50
BCS-815 Cell Cables50
BCS-805/810 Cell Cables51
BCS-8Xx Battery Holders51
Cell Cable to a Battery Cell53
Two Electrode Connection to a Battery Cell53
Four Electrode Connection to a Battery Cell53
Electrode Connection Using Coin Cell Holder53
Advanced Features54
Control and Measurement Modes54
Sine Generator54
Temperature Measurement54
Virtual BCS-8Xx55
Maintenance57
Firmware Upgrade/Downgrade with BT-Lab  Software57
Ventilation61
Fuses61
BCS-8Xx Power Contour Plots61
Power Contour Plot for BCS-80562
Power Contour Plot for BCS-81063
Power Contour Plot for BCS-81564
In Case of any Problems67
Technical Specifications68
Electrical Specifications68
Mechanical Specifications69
Environmental70
BCS-815 Specifications71
BCS-810 Specifications72
BCS-805 Specifications73
BCS-COM Specifications73
PC Requirements74
Troubleshooting75
Control / Measurement Issues75
EIS Verification: Dummy Cell BCS75
DC Verification: Dummy Cell DC-BCS76
Calibration: BCS-Cal76
Data Saving77
PC Disconnection77
Effects of Computer Save Options on Data Recording77
Appendix78
Simplified Electrical Split-Phases Diagrams78
Electrical Schematic Documentation79
USA/CAN PDU Model: Power Line79
USA/CAN PDU Model: Logic Line80
European PDU Model: Power Line81
European PDU Model: Logic Line82
Electrical Symbols Used83
EC and UKCA Declaration of Conformity85
Glossary87

BioLogic BCS-810 - Page 39

Table of Contents

Related product manuals