Bosch Solution 16i - Page 103

9-13
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Comms Programming
12) Using the numeric keys, enter all the digits for CLI
number 3. You can change a single digit by
scrolling the cursor left or right. For special
characters including, pause, * or #, use the up and
down arrow keys.
13) Press [OK] to save CLI number 3.
14) When nished Press [OK] to save and exit or press
[MENU] to exit without saving.
i
Note
Up to 3 Phone numbers can be entered for CLI Call
Line Identication for remote access detection. You
must enter STD code plus the compete number for
this option to work. Press [OK] after each telephone
number is entered to save and move to the next
number.
R EP OR TIN G O PTI ON S
Comms > Dialler Reporting > L540
TX Format Dest 1

MENU 5-4-0
00 = Disable 0 1
01 = Contact ID 07 = Domestic
02 = SIA 08 = Voice 13 = Reserved
03 = Serial STU 09 = SIA + 14 = SMS - No Parity
04 = GSM 10 = Reserved 15 = Reserved
05 = WEB MAIL 11 = Reserved
06 = SMS 12 = Ethernet
This menu allows you to program the transmission format
or language the panel will use to send event reports to
Destination 1. The panel has two separate destinations
that reports can be sent to and each one can be set to
use a dierent transmission format depending on the
application.
At factory default, all reports are routed to Destination 1.
1) Enter your Installer PIN + [MENU].
2) Press [5] + [4] + [0] + [OK]. The keypad will display
the current Transmission Format for Destination 1.
d= 01
3) Use the numeric keys to enterthe Transmission
Format required then Press [OK] to save and exit or
press [MENU] to exit without saving.
Comms > Dialler Reporting > L541
TX Format Dest 2

MENU 5-4-1
00 = Disable 0 1
01 = Contact ID 07 = Domestic
02 = SIA 08 = Voice 13 = Reserved
03 = Serial STU 09 = SIA + 14 = SMS - No Parity
04 = GSM 10 = Reserved 15 = Reserved
05 = WEB MAIL 11 = Reserved
06 = SMS 12 = Ethernet
This menu allows you to program the transmission format
or language the panel will use to send event reports to
Destination 2.
At factory default, all reports are routed to Destination 1.
1) Enter your Installer PIN + [MENU].
2) Press [5] + [4] + [1] + [OK]. The keypad will display
the current Transmission Format for Destination 2.
d= 01
3) Use the numeric keys to enter the Transmission
Format required, then Press [OK] to save and exit or
press [MENU] to exit without saving.
Comms > Dialler Reporting > L542
Test Route

MENU 5-4-2
(*** System Wide Parameter ***)
0 1
00 = Report Events To Log Only
01 = Report Events To Destination 1 + Log
02 = Report Events To Destination 2 + Log
03 = Report Events To Destination 1 & Destination 2 + Log
04 = Report Events To Dest 2 If Dest 1 Fails + Log
This menu programs which destination will be used to
send both manual and automatic test reports.
1) Enter your Installer PIN + [MENU].
2) Enter [5] + [4] + [2] + [OK]. The keypad will display
the current Test Route.
d= 01
3) Use the numeric keys to enter the Test Route
required, then press [OK] to save and exit or press
[MENU] to exit without saving.