Bosch Solution 16i - Page 97

9-7
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Comms Programming
3) Use the up and down arrow keys to highlight the
option then press the [ON] key to enable or the
[OFF] key to disable.
4) Repeat Step 3 until all options are programmed as
required, then press [OK] to save and exit or press
[MENU] to exit without saving.
Display Telephone Line Fail
This option sets the panel to display a trouble signal on
the keypad display when the panel detects a teleco line
fail condition.
Report Telephone Line Fail
This option sets the panel to send a line fail report
when it detects a telco line fail condition. If congured,
the panel is able to report this signal via an alternative
reporting method such as the GSM cellular network.
If no alternative route exists then the panel will send the
signal and restore when the PSTN line is reconnected.
Alarm On Telephone Line Fail If Armed
This option sets the panel to trigger an alarm when the
telco line fails provided that the area is turned All On or
Part On. In a multi-area system this option is global and
will be triggered if only one area in the system is in the
armed state. The alarm will continue to sound until a
valid PIN is entered or the siren timer expires.
Alarm On Telephone Line Fail If Disarmed
This option sets the panel to trigger an alarm when the
telco line fails provided that the area is turned OFF or
disarmed. In a multi-area system this option is global and
will be triggered if only one area in the system is in the
disarmed state. The alarm will continue to sound until a
valid PIN is entered or the siren timer expires.
Display ‘Phone In Use’
This option allows the keypad to display Phone In Use
when the telephone line has been looped by the control
panel for either incoming or outgoing calls. If this option
is disabled, no indication is provided on the keypad.
i
Note
The dialler status indicator LED located on the main
panel will always show the status of the dialler. See
Section 3 - Wiring Diagrams for more information.
Comms > Properties > L523
Country

MENU 5-2-3
(*** System Wide Parameter ***)
0 1
01 = Australia 06 = Spain 11 = Bulgaria
02 = New Zealand 07 = Portugal 12 = China
03 = Italy 08 = Hungary 13 = Hong Kong
04 = Greece 09 = Czech Republic 14 = Malaysia
05 = Cyprus 10 = Poland 15 = Brazil
This menu automatically sets the dialling parameters
including dial and busy tones etc. for the country the
panel is working in.
1) Enter your Installer PIN + [MENU].
2) Enter [5] + [2] + [3] + [OK]. The keypad will prompt
you to enter the country required. The default
country is Australia.
3) Use the numberic keys [0] to [9] to select the
appropriate country, then press [OK].
Ln=
4) Press [OK] to conrm and save and exit or press
[MENU] to exit without saving.
i
Note
For correct dialler operation, you must make sure
that the correct country selection is made for your
location. If your country is not listed here please
contact your Digiex distibutor.
Comms > Properties > L527
Set SMS Password

MENU 5-2-7
p a s s w d
This menu sets the SMS password which is required
whenever SMS reporting is selected. The password will
typically be dened by the service provider or Telco carrier
who you are using to route the message.
By default the SMS password is set to suit the Telstra
Network in Australia.
1) Enter your Installer PIN + [MENU].
2) Enter [5]+[2]+[7] + [OK]. The keypad will display the
current SMS password.
3) Use the arrow and number keys to move and
change text. At any time you can press the [OFF]
key to clear the text from the current cursor
position to the end of the line.