~~~~~~~~~~~~~~~~~~~~~
••••
Connecting
to
a
Co~puter
The following recordings cannot be transferred
to the computer using MyDVD for Canon:
- Recordings made
in
LP
mode
in
widescreen
(16:9 aspect ratio)
on
a DVD-RW initialized
in
VR mode.
- Photomovie scenes created with this
camcorder.
- A finalized disc
is
not inserted
in
the
camcorder.
- A brand new disc
is
not inserted
in
the
computer's DVD drive.
- The disc
in
the camcorder
is
a DVD-RW
recorded
in
VR mode but the disc
in
the
computer's DVD drive
is
a DVD-R disc.
- The disc
in
the computer's DVD-drive
is
a
dual-layered disc.
• If none
of
the previous applies but
[ddJ
!IV')
still
does not light
up,
look for the
~
icon
in
the
computer's desktop toolbar. If
~
does not
appear, disconnect the USB cable from both,
the camcorder and the computer. Restart the
computer and turn the camcorder off and then
on again. Then, connect the camcorder to the
computer again.
Transferring
Recordings
to
the
Computer
1
Insert
the
source
disc
into
the
camcorder.
You
can use any disc regardless
of
whether it
is
finalized or not.
2 Run MyDVD
for
Canon.
3
Click
on the "DVD-Video"
option
in
the
New Project tab.
4
Check
that
the DISC access
lamp
is
not
on
or
flashing
and
click
on
the
"Open
Disc"
icon.
S
Click
on the
"Import"
button.
Thumbnails
of
the imported scenes
and still images will be displayed
in
the
video project screen.
6 To save the project,
click
on
"Save
Project"
from
the
Project
Tasks
palette.
The scenes and still images displayed
in
the main screen will
be
saved.
--_._~
OJMPORTANT
Creating
Backup
Copies
of
your
DVD
1
Insert
a finalized
disc
into
the
camcorder.
2 Run MyDVD
for
Canon.
3
Click
on
the
"Make
a
Backup
DVD"
option
in
the
New
Project
tab.
4 Selectthe
camcorder
as
the
"Device
to
read
from"
.
S Select-the
computer's
DVD
drive
(with
writing
capabilities) as
the
"Device
to
write
to".
Ifyour computer
is
not equipped with a
DVD drive with writing capabilities,
select the camcorder also as the
"Device to write to".
6
Check
that
the
DISC access
lamp
is
not
on
or
flashing
and
click
on
the
"Copy"
button.
7
Follow
the
indications
on the
screen.
If you selected the camcorder itself as
the "Device to write to", after the
camcorder finishes reading the
original disc, remove it and insert a
brand new DVD-R or DVD-RW disc
into the camcorder.
8 When the
"Your
disc
was
created
successfu
lIy"
screen appears,
click
"OK".
The copied disc will be finalized and
automatically ejected from the drive.
•
To
make a copy
of
a disc recorded
in
VR
mode, be certain to insert a DVD-RW disc into
the computer's DVD drive.
• The software does not support writing on
dual-layered discs.
• Always use a brand new disc as the target
disc
in
the computer's DVD drive or the
camcorder.
• If you are using a computer's DVD drive to
make the backup copy you can also use a fully
erased DVD-RW disc.
To
fully erase a DVD-RW
disc you will need DVD authoring software.
---~
o
IMPORTANT
To Next Page
Loading...
